The steel shaft with two different diameters rotates at 4.9 Hz. The power supplied to gear C is 54.1 kW, of which 26.9 kW is removed by gear B. Find the angle of rotation of gear A relative to gear Cif d = 55.5 mm, h = 68.9 mm, L = 4.2 m, M = 2.8 m, and G = 83.46 Gpa. Round off the final answer to two decimal places.

Q: The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A…

A:

Q: A gear train is made up of five spur gears as shown in the figure. Gear 2 is driver and gear 6 is…

A: Given data, Figure shown gear train is made of five spur gears. Where,  Gear 2 is driver and gear 6…

Q: for the gear train in below sketch that input gear has 5 kW of power and rotates clockwise at…

A:

Q: a) Fig. 3 shows a gear train that is attached to a rack labelled A. The rack is capable of moving up…

A: Fig. 3 shows a gear train that is attached to a rack labelled A. The rack is capable of moving up…

Q: The required diameter of shaft AB is mm. Determine the required diameter of shaft CD. (Round the…

A: Torque of the rodShear stress Given Radius of

Q: A car's engine is producing 93 ft-lb of torque and is in a gear that gives an overall gear reduction…

A:

Q: In the gear system shown, the motor applies a 190 lb-ft torque to the gear at A. A torque of Tc=392…

A:

Q: Determine the angle through which end A rotates, if a torque of TA = 88 N-m is applied at A. Note:…

A:

Q: calculate the indexing for the following: 1.  1623 divisions 2. 1124 divisions

A: Given DataDivisionsN=16232-N=1124 three plates

Q: Determine the thickness (mm) of a spur gear tooth with a diametral pitch of 7.01, measured along the…

A:

Q: The center distance between the two gear is 250mm and module is 5cm. Find the number of the teeth of…

A: module=diameter/teeth

Q: In the figure below, Gears B and C represent a compound gear and have the following details. The…

A: number of teeth t A=100 tB=40 tc=80 tD=20 input torque  Ti=42 Nm speed of gear A NA=2400 rev/min…

Q: A compound shaft drives three gears. Segments (1) and (2) of the compound shaft are hollow aluminum…

A:

Q: Two solid circular shafts are connected by two rigid ab is a composite shaft. Determine the angle of…

A: The radius of gear B is The radius of gear C is The outer radius of AB is The inner radius of AB is…

Q: Consider the following steel shaft with varying shaft diameter. Determine the rotation of D with…

A:

Q: Number of teeth of gears z1: 22 Tooth numbers of gears z2: 90 Tooth numbers of gears z3: 23 Tooth…

A: Here motor is driving the gear 1 shaft which is in mesh with gear 2. Gear 2 and 3 are at same shaft…

Q: 7.15 Two left-hand helical gears having the same helix angle are used to connect two shafts 60°…

A: (a) The number of teeth on gear: ZG = 62 teeth (b) The number of teeth on pinion: ZP = 25 teeth

Q: A power transmission shaft is to carry a steady 30 horsepower while rotating at 1000 rpm. Specify a…

A:

Q: Below is the arrangement for a gear train. A motor delivers 200-hp at 540-RPM to the input gear A.…

A: The speed of gear A, NA = 540 rpmThe power delivers by motor, P = 200 hp

Q: A compound shaft drives three gears. Segments (1) and (2) of the compound shaft are hollow aluminum…

A:

Q: consider a planetary train in the figure the number of teeth on gear sol (2) is Z2= 30, the number…

A:

Q: If the circular cam a has wa = 15 rad/sec clockwise, find the velocity of point B (in/sec) and the…

A: The given figure is re-represented with some other important points as shown in the below.From the…

Q: 2. A gear train shown in the figure consist of gears P, Q, R, and S. Gear Q and Gear R are mounted…

A:

Q: 50 teeth A 90⁰ B 80 teeth C 60 teeth

A: Given,  NA= 700 rpm

Q: In a spur gear arrangement, the driver has 90 teeth of 38 mm pitch. Find the power, if it can…

A: Given that Pitch= 38 mm Tangential force = 130 N Speed = 100 rpm

Q: Gear 1 has a module of 2 and 26 teeth. This gear drives Gear 2 whose speed is 271.0 rpm. The shaft…

A: Given: The teen on gear 1 is T1=26, The module of gear 1 is m1=2, The speed of gear 2 is N2=271…

Q: The Smm module with 40 number of teeth gear is used to transmit 42.3 kw power at 350 rpm .Find the…

A:

Q: The spur gearing arrangement  made of two parallel shafts,whose pitch circle diameters of driven and…

A: Gear: The gear is rotating part of the mechanical device. The gears are having the number of teeth…

Q: A hollow round steel shaft has a torque of 600 ft-lb. The shaft has an outside diameter of 1.25 in,…

A:

Q: n find the speed of the gear F.

A: Given data: A compound train consists of six gears. the  no teeth on gears as follows:NA=100…

Q: 4. For the extended epicyclic gear train shown. Gears 1, 3, and 6 have internal teeth while gears 2,…

A: In gear train , we knowvelocity ration=velocity of first drivervelocity of last driverBy using…

Q: consider a planetary train in the figure the number of teeth on gear sol (2) is Z2= 30, the number…

A: Write the given data. Z2=30Z3=20Z4=70ω2=300 rpmω4=200 rpm

Q: The steel shaft with two different diameters rotates at 4.3 Hz. The power supplied to gear C is 48.5…

A:

Q: Below is the arrangement for a gear train. A motor delivers 200-hp at 540-RPM to the input gear A.…

A: Given:The gear A rotates clockwise CW.Gear B and C are on the same shaft and gear D and E are on…

Q: 20° pressure angle. Gear 3 is an idler (b) Find the torque T4c that gear 4 exerts on shaft c.

A: Calculate the speed of the shaft in rad/sec. Here, the speed of the shaft in rev/min is .…

Q: You have been asked by your engineering company to design a complete gear and shaft system shaft…

A: Given:- TA=15 kN-m(clockwise direction),TB=30 kN-m(clockwise direction),TC=75 kN-m(anti-clockwise…

Q: Each of two gears in a mesh has 60 teeth and a module of 6 mm. The teeth are of involute profile.…

A: Data given-  T = 60  m = 6 mm  Arc of contact = 2.5 × circular pitch

Q: The figure shows a rotating geared system. A torque of 3N is applied to an input gear in order to…

A: Given data: Input gear teeth = z = 11 Output gear teeth = Z = 99 Assuming that  Input gear torque =…

Q: The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque…

A:

Q: The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A…

A:

Q: In a spur gear arrangement, the driver has 80 teeth of 39 mm pitch. Find the power, if it can…

A: Given:Teeth on driver, T=80 teethPitch of driver, P=39 mmtangential force, F=60 NSpeed, N=150 rpm

Q: Determine the number of teeth for gear E. Determine the Pitch Diameter PD of gear F. Determine…

A: Approach to solving the question: USING THE RELATION OF TEETH, RMP,PITHC DIAMTERNOMENCLATURE: NO. OF…

Q: A gear box has an input speed of 1,809 rev/min clockwise and an output speed of 475 rev/min…

A: Ni=1809 revminNo=475 rev/minPi=49 kWη=0.77Po=?

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.