A gear box has an input speed of 1,809 rev/min clockwise and an output speed of 475 rev/min anticlockwise. The input power is 49 kW and the efficiency is 0.77. Determine the input output Power in kW

Q: The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A…

A:

Q: Q3: For the gear trains shown below, What is the velocity and direction of output gear? A 60T D 201…

A: . GivenTA=20NA=60rpmTB=60NB=?TC=10NC=?

Q: 1 to one module.

A:

Q: What are the direction and speed of the driver gear (D1) in the figure below if the driven gear (D2)…

A:

Q: Determine the horsepower of a 6 cylinder 4 stroke continental engine having a bore equal to 3.875 in…

A:

Q: If gear A rotates at 2400 rev/minute calculate the velocity ratio and mechanical advantage

A:

Q: For the complex gear train shown, calculate the torque ratio (TR). W2 = @3 W4 130 rpm N, = 45 %3D N2…

A: Given data: The number of teeth in the first gear is N1 = 45. The number of teeth in the second…

Q: 2. The spur gear train drive shown in question 1 (as bearing D and E) fitted with full journal…

A:

Q: Examine the gear drive shown.  The small driving gear has 15 teeth, DP = 8, RPM = 1200, Torque = 4…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: A gear box has an input speed of 2,000.00 rev/min clockwise and an output speed of 500.00 rev/min…

A: Given data, Nin = Input speed = 2000 rev/min Nout = Output speed = 500 rev/min Pin = Input power =…

Q: Two equal involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angle are in mesh.…

A: According to the given data Number of teeth (T)=40 Module (m)=3mm Pressure angle ϕ=20° Speed…

Q: In the figure below, C and D represents brakes, which can be used to stop the rotation of either…

A: C represent gear 4  D represent gear 8 T denotes Teeth in this solution And N denotes rpm

Q: The gear train shown in the image has a pressure angle of 20° and a DP of 16. Shaft 2 is turning at…

A:

Q: The machine design has stated that a 2.5 kW electric motor with an input speed of 1000 RPM is needed…

A: Given Data The power of the electric motor is: P=2.5 kW The input speed is: N=1000 RPM Th overall…

Q: For the gear train shown below determine the velocity ratio, output speed, output direction, output…

A: Given:  No. of Teeth in Gear A, ZA = 20 Rotational Speed of Gear A, NA = 3000 rpm  (CW) Input Torque…

Q: Input shaft of the gear train shown below rotates at 1,500 RPM. The output shaft must rotate exactly…

A:

Q: e marimum velocity of slidi

A:

Q: An epicyclic gear in figure 1 consists of ring gear, planet gear and sun gear. The ring gear has 72…

A: Given Data Ts=32 TR=72 Y=+20

Q: The figure shows a rotating geared system. A torque of 3N is applied to an input gear in order to…

A: Given data: Input gear teeth = z = 11 Output gear teeth = Z = 99 Assuming that  Input gear torque =…

Q: A motor has pinion gear with 14 teeth and is meshed with a gear with 52 teeth. The gear is attached…

A:

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.