The steel bar in the figure has a diameter of 60 mm. As the shaft is loaded with the CDE rigid arm as shown in the figure; a) Find the normal and shear stresses at point B and plot on a cubic elementary part ? b) Find the principal and shear stresses at point B. ?

Q: 3. „ please calculate and 30

A: given: stress in x direction(σx)=0stress in y-direction (σy)=-σy(compressive)shear stress in xy…

Q: The screw clamp shown in the figure applies a P = 500 N pressing force to the wooden blocks between…

A:

Q: 3.7-5 The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in.,…

A:

Q: Determine the time required to acceierate a counter shaft of rotating mass 500 kg and radius of…

A: Given that, Mass m=500 kg,   N=250 rpm Radius of gyration k=200 mm=0.2 m External radii of plate…

Q: (A,) See the figure below. There are two torques applied at B and D. Segment CD is a tube, while AB…

A: In the given problem, the dimensions and Modulus of rigidity have been converted to feet. Radius,…

Q: 6. The steel shaft of a socket wrench is 12 mm in diameter and 450 mm long (see figure). If the…

A:

Q: 1. See figure below and solve for the maximum value of torque the composite shaft can accommodate…

A:

Q: For the stress state shown in the figure; Using Mohr's circle calculate: a) Principal stresses…

A: Given data and Initial Calculation:-

Q: 3.5-2 The outer diameter of the hollow aluminum shaft (see figure) is d 2 =100 mm^ and the inner…

A:

Q: 400 mm 400 mm 11th. Of the spindle in the figure AB the portion is full and BC part is empty. To the…

A: Given, Total applied Torque (T)= 8kNm Modulus of Rigidity (G)= 80GPA Solution Divide the spindle…

Q: ! Required information The steel eyebolt shown in the figure is loaded with a force F= 86 lbf. The…

A:

Q: As shown in the figure, a force P-150N and a torsional moment T=400N.m are applied on the free end…

A: Draw the free-body diagram of the shaft.

Q: simply supported beam of inverted T-section shown in Figure 5, of the working stresses are 48 MPa in…

A: The maximum tensile stress is .The maximum compressive stress is .The maximum shear stress is

Q: C ):- Draw the MC stress elemen Find:-

A: given:σX=20ksiσy=14ksi

Q: When drilling a hole in a table leg, a furnituremaker uses a hand-operated drill (see figure) with…

A: The shear stress in the bar, when it is subjected to torsional moment can be calculated using the…

Q: P = 500 N pressing force to the wooden blocks between the jaws. It case; a) Calculate the greatest…

A:

Q: The outer diameter of the solid steel pipe shown in the figure is 25 mm. If the pipe is fixed at…

A:

Q: A cantilevered beam of rectangular section (b width=3 inches ), h camber=12 inches ) is subjected to…

A: A cantilevered beam of rectangular section width b= 3 in h=12 in load P=17 lb  c=2.5 ft from the…

Q: A flat bar with a hole (see figure) has widths b = 60 mm and c = 40 mm. The fillets have radii equal…

A: b = 60 mm c = 40 mm R = 5 mm to determine diameter dmax of the largest hole

Q: A beam made of Al 2014-T6 aluminum alloy is loaded by an oblique bending moment of M= 5 kN.m as…

A: Solution: a) Centroid of the cross-section y¯ can be calculated by, Let area A1 = 90×10=900mm2…

Q: A R Mz Mx x y

A:

Q: A bending moment of M=150 kips in is applied at the cross section of bearn shown in Figure Question…

A: Answer: ◆ The maximum tensile stress is 9.57568 ksi. ◆ The maximum compressive stress is 14.91330…

Q: tube subjected to pr times the inner radi hear strain in the tu ner surface? allowable rate of tv

A:

Q: 1 of 1 -1.5m- Q: Aluminum shaft of 30mm diameter and 1.5m lenght is subjected to a torque of 500N.m…

A:

Q: A motor driving a solid circular steel shaft transmits 30 kW to a gear at B (as shown). The…

A: Here is the solution for the above question.

Q: subjected to pure tor s the inner radius n. strain in the tube is m

A:

Q: 7.2-5 The stresses acting on element A on the web of a train rail (see figure part a) are found to…

A:

Q: The outer diameter of the solid steel pipe shown in the figure is 25 mm. If the pipe is fixed at…

A: Principle Stresses : planes in which plane shear stress is zero are known as principle plane and…

Q: In the figure, a force of 1 kN is applied by means of an arm connected to a shaft with a diameter of…

A:

Q: 3. A beam with a rectangular cross section of dimensions ax 1.5a is made from a b in the figure…

A:

Q: In the figure below, A 50 mm shaft is subjected to a reversed load P= 2700 N. Find the length (L),…

A:

Q: The screw clamp shown in the figure applies a P = 500 N pressing force to the wooden blocks between…

A:

Q: A flat bar with a hole (see figure) has widths b = 60 mm and c = 40 mm. The fillets have radii equal…

A: The stress which is normal to a cross-section is termed as normal stress and the force which is…