Find the stresses and compressions in each section of the composite member shown in Figure. Use Es- 30 x 10 psi, Ea - 10 psi, Eb-15 x 10 psi, and the minimum number of linear elements. Steel (A,=8 in) Brass (A,-4 in) 2500 lb 2000 Ib 2500 Ib 16 in 16 in 16 in. Aluminum (A,=6 in)

Q: This still doesnt answer how to get points 2,  2', and 1', so how did you get it?

A: Itis asked to explain how the state points 2, 2' and 1' are obtained

Q: Show your complete solution including the diagrams and box your final answers with their appropriate…

A:

Q: 2. Draw the sketch of 'Drilling machine' and explain any four parts. Use pencil to draw the neat…

A:

Q: how o create all parts list after the drawing ?

A: Given question: how to create all parts list after the drawing ?

Q: Part C - Radius of curvature for AB and BC Determine the radius of curvature for AB, PAB, and for…

A:

Q: 2. Write 5 details found on the drawing title block?

A: The bottom right hand corner block in engineering drawing sheet is known as title block. This block…

Q: In Part a, could you please explain where the 4 comes from on the line before the answer.

A:

Q: In a workshop, Drilling operator is working on a Drilling machine. The drilling operator needs to…

A:

Q: Are you able to show an answer in terms of using formula from start to finish to get the answer…

A: Are you able to show an answer in terms of using formula from start to finish to get the answer…

Q: 8. A note in the comment section of a title block mentions that all faces should have a +.10…

A: Circularity (roundness) tolerance is 2-D in nature.

Q: Q3: Mark the Following True or False 1. Hidden lines are used in sectioned area when they are needed…

A: 1.TRUE 2. TRUE 3.TRUE 4.FALSE 5. FALSE 6.FALSE 7.TRUE 8.FALSE 9.FALSE 10.FALSE 11.TRUE 12.TRUE…

Q: Discuss how the Cylindrical Square is used.

A: A cylinder square is used for checking the squareness of vertical axis with reference to horizontal…

Q: 3. What makes EDM become a key in tool and die making machine tool ?

A: The main reason of using EDM in die making process are:-

Q: can you please write it in a proper way?

A:

Q: Develop two possible hierarchies for assembling a model from the parts given below: Top Pins…

A: Given question: Develop two possible hierarchies for assembling a model from the parts given below:…

Q: With reference to the drawing callout in figure 5 below, which part(s) would 'pass' or 'fail' along…

A: Data given-  Dimensions of standard size  0.25±0.01 So tolerance is equal to 0.02  And the upper…

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: Write TRUE is the statement/s is True. If the statement is false, identify the word/s that makes the…

A: The chip compression ratio can be defined as the ratio of the chip thickness and uncut chip…

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: short notes on any two types of chips formed during metal cutting operation

A: Metal cutting is defined as "the act of eliminating undesirable material from a block of metal in…

Q: of the table) and free to move if a force is applied. A force is applied on it as the arrow…

A:

Q: A piece of 12-gauge sheet metal is 7⁄64 inch thick. A stack of sheet metal is171⁄2 inches thick. How…

A: Given12 guage sheet metal sheet thickness t=7/64 inchthickness of stacked sheets t2=171 2inches

Q: Write the types of keys and sketch freehand of them with dimensions and equations.

A: A key is a machine element that is fitted in the axial direction with the mating parts in pulleys…

Q: PART VI. Given that f(x,y) = (x +y)/2k, where x=-1,1,2 and y= 0,2,4 1. Find k 2. Find the marginal…

A:

Q: 1. How is fraction changed to decimal? A. Divide the denominator by the numerator B. Divide the…

A: Since we answer only one question at a time, we will answer the first one. Please resubmit the…

Q: How do you solve parts a,b and c?

A:

Q: I need these two parts answered (Multiple Choice). If you can not answer all two parts please leave…

A: Problem 1To determine the tolerance specified for the depth of groove in the enlarged view, refer to…

Q: Learning Goal: To determine the equation for the elastic curve of a beam that is subjected to an…

A:

Q: Part C - Maximum allowable axial force for fixed-and-free-end support If the cylindrical column is…

A:

Q: Draw the and B A.F.D&S.F.D& B.M.D (KN.M

A: To draw axial ,shear and bending moment diagram

Q: I need this part answered according to the disrections provided in the image.

A: Match each of the following terms to the phrase that describes it

Q: Which of the following process for sheet metal cutting, the cut piece is the desired part? Shearing…

A:

Q: I need problems 7, 8, and 9 answered pertaining to the print attached below.

A: Cutting plane line:Cutting plane lines are represented by dotted chain line as shown in the figure.…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.