Match each of the following terms to the phrase that describes it. Answers are used only once. History Order by someone to permanently revise the part and print. 1. ECO 2. One of three approaches for multiple sheet changes. Pending 3. Status of sheets 4. Waiting for paperwork to go through. Approved 5. Two columns marked with SH and REV By sheet 6. headings. DD 7. Appropriate as part of the name for the revision Was 8 block. Zone 9. Initials of someone in revision block. 10. Underlined number

Match each of the following terms to the phrase that describes it. Answers are used only once. History Order by someone to permanently revise the part and print. 1. ECO 2. One of three approaches for multiple sheet changes. Pending 3. Status of sheets 4. Waiting for paperwork to go through. Approved 5. Two columns marked with SH and REV By sheet 6. headings. DD 7. Appropriate as part of the name for the revision Was 8 block. Zone 9. Initials of someone in revision block. 10. Underlined number

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: . a. On the part shown, show a angularity specification to orient the angled surface in relation to…

Q: The degree of precision of a quadrature formula whose error term is : O 4 2

A: Givenerror term is h23f3ξ

Q: two pulleys are connected by a belt. The nubers of RPM of the two pulleys vary inversely as their…

A: Given data: The diameter of pulley 1 is, d1 = 25 cm. The diameter of pulley 2 is, d2 = 40 cm. The…

Q: 2.34 Determine the resultant of the three forces of Prob. 2.22. Answer

A: Given:The three forces are:F1=800 NF2=408 NF3=424 N

Q: When does the reduction in the dimensions occur?

A: Reducing of dimensions is done in the following conditions. Reducing of dimensions of a workpiece…

Q: Above is a 5 speed manual transmission gearbox. The gear selector fork is an assembly which the user…

A: Gear ratio is defined as ratio of driven gear's teeth to driver gear teeth. G1/2 = T2/T1 G1/3 =…

Q: I didn't understand how you fond the angle teta

A: For solution refer below images.

Q: Answer the following in the space provided. 39. Suppose the engine in a vehicle is delivering 550…

A: Data given- T1 = 550 lb -ft N1 = 5000 rpm Gear ratio = 1.5/ 1 = 1.5

Q: Give all the location dimensions between the datum target areas , A1 and A2. X = _________________,…

A: Give all the location dimensions between the datum target areas , A1 and A2.X =0 , Y =74 , Z =…

Q: 6) PLEASE BE CLEAR ON

A: Given that f=220 GHzd=48.8 cm =0.488 mb) Part d=1.96 mλ=1.6 cm

Q: Q2. (Answer One) AW-+号how tht +-0 ) "-/(). show that +-

A: Given To find prove the following

Q: I need help with question number 15 that is pertaining to the print provided.

A: 15.The unidirectional system is used here for the dimension placing. The unidirectional system is…

Q: how did the equation simplify to a = 0.984?

Q: n the figure, front (1st picture) and left (2nd picture) views of a machine part are given. Based on…

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: The result that I got after solving it was 463.0721, is that correct?

A: Given: d= 0.27in τ capacity=26.5 ksi = 26500 psi. Factor of safety =1.6 To find: The maximum T-force…

Q: An engineer is creating a solid model of a simple gear using SolidWorks. Choose the correct…

Q: Hello, I need help with the answer of 3.14 from the picture, please.

Q: Can you pls slove this question briefly with hand written notes and diagram

Q: Select the correct statement below regarding the two solid model parts shown. (A) (B) It is easiest…

A: In the figure two solid model parts are given. The extrusion is in which the two dimensional shape…

Q: Identify the drawings as isometric, trimetric, oblque or perspective. A. B

A: Isometric projection is a technique used in technical and engineering drawings to visually…

Q: Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A=52 B=19 Your…

A: Given : To find : Volume of the body

Q: Given the top and front views, sketch the right face.

A: According to the details provided in the question. Top view and front view is given we need to draw…

Concept explainers

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing. 

Question

I need this part answered according to the disrections provided in the image.

Match each of the following terms to the phrase that describes it. Answers are used
only once.
History
Order by someone to
permanently revise the
part and print.
1.
ECO
2.
One of three approaches
for multiple sheet
changes.
Pending
3.
Status of sheets
4.
Waiting for paperwork to
go through.
Approved
5.
Two columns marked
with SH and REV
By sheet
6.
headings.
DD
7.
Appropriate as part of
the name for the revision
Was
8
block.
Zone
9.
Initials of someone in
revision block.
10. Underlined number

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

How is the mohrs circle plotted? what values were plotted
I need help solving problem numbers 4--15.
I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5. 1 pass 2 fail 3 fail 4 pass
I need these three parts answered, if you are unable to answer all three parts please leave it for another tutor to answer, thank you.
Apply geometric tolerancing to part according to the instructions below. This exercise will provide you with experience in correctly applying and interpreting geometric tolerancing symbology. If you have trouble applying the symbols, page through this unit looking for similar examples. The Hole Bar in this unit is a good reference. Draw symbols and feature control frames clearly and neatly. 1. Establish the right face in the side view as datum feature A. Qualify this feature with a flatness of .005. 2. Establish the top surface in the front view as datum feature B. Qualify this feature with a perpendicularity of .005 to datum feature A. 3. Establish the left surface in the front view as datum feature C. Qualify this feature with a perpendicularity of .005 to datum features A and B. 4. Establish all necessary dimensions as basic. 5. Position the .250 hole within a diameter of .005 RFS relative to datum features A,B,C. 6. Position the three holes within a diamter of .012 at MMC relative…
kindly answer it
I need help answering this quick review pertaining to the print provided.
1. What revision is this part on? 2. How many dimensions are expressed using the limit method? 3. What is the surface texture in microinches is specified for the cylinder surface with a maximum material condition of 1.250"? Leave out the units, it is microinches, just type the number. Thanks :)!
Please help. I need help with all 4 questions. Apply geometric tolerancing to part according to the instructions below. This exercise will provide you with experience in correctly applying and interpreting geometric tolerancing symbology. If you have trouble applying the symbols, page through this unit looking for similar examples. The Hole Bar in this unit is a good reference. Draw symbols and feature control frames clearly and neatly. 1. Establish all necessary basic dimensions. 2. Position the .250 hole within a diameter of .005 RFS relative to datum features A,B,C. 3. Position the three holes within a diamter of .012 at MMC relative to datum features A,B,C. 4. In the front view, identify the upper right corner as point "Y" and the lower left corner as point "X". Apply a profile tolerance of .020 between points X and Y relative to datum features A,B,C. Please refer to the attached image.
In order to measure the extension of perfection in the mesh, the method of skewness is used.
How would you determine final dimensions using the plus & minus method for question #D??