A pressure vessel of thickness 10 mm and inner radius 220 mm is subjected to an internal pressure of 5 MPa and torsional load of 150 N.m. T a) Determine the stress state at point A and show the results on a cubic volume element given below the figure. b) Determine the principal stresses and the maximum in- A T plane shear stress cases Mohr's circle at point A. Specify the orientation of the element in each case. Note: The results obtained by using transformation equations will not be graded even they are correct.

A pressure vessel of thickness 10 mm and inner radius 220 mm is subjected to an internal pressure of 5 MPa and torsional load of 150 N.m. T a) Determine the stress state at point A and show the results on a cubic volume element given below the figure. b) Determine the principal stresses and the maximum in- A T plane shear stress cases Mohr's circle at point A. Specify the orientation of the element in each case. Note: The results obtained by using transformation equations will not be graded even they are correct.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure 1a shows a concrete beam supported by twosolid circular columns. Column AB is made from steeland column CD is made from aluminium, see the stressstrain graphs in Figure 1b. The concrete beam issubjected to the load P as shown in Figure 1a.1.1 Determine the normal stress in column AB and column CD. 1.2 Determine the relative change in angle of point Cto A in degrees. Given: P= 100 KN L1= 3m L2= 2m L3= 1m dAB= 60mm dCD= 60mm
Figure shows a beam made from bronze subjected to a 3.5kN.m bending couple and its respective tensile properties. i) With aid of illustration, draw the deformation of the bean and locate the position where the beam experience maximum tensile stress (αmax)t and maximum compressive stress (αmax)c. Accordingly. Determine the magnitude of these two stresses. ii) Sketch the two-dimensional stress distribution acting on point A and point B over the cross-sectional area of the beam as observed from side view. Estimate the magnitude of the stresses at those two points.
Read the question carefully and give me answer according to the question
(3) The cantilever bar as shown on next page is made of a brittle material. At D, Fx-300 lb. F-250 lb, and F-100 lb. Determine the precise location of critical stress element at the cross section at A. Determine the magnitude for each of the stress components considering the stress concentration at A. Find the principal stresses and the maximum shear stress at this location. 2 in 1-in dia. -in R. 12 in
Question 1: For the state of plane stress as shown in the Figure: Construct the Mohr's circle. Determine the principal stresses. Find the orientation of the principal plane. Compare the results of (b) and (e) with equation method. 12 MPa 6 MPa S MPa
Example vacuum pressure): A thick cylinder of inner radius 8cm and outer radius 12 cm is subjected to an external pressure of -0.09M Pa. Internal pressure is atmospheric. Determine (a) the radial and tangential stress distribution across the the thickness, (b) the axial component of stress, if the ends of the cylinder are fixed. Assume v=0.3 and (c) maximum shear stress
nc./Johan H σy 7.2-1 The stresses on the bottom surface of a fuel tanker (figure part a) are known to be o = 7750 psi, = 1175 psi, and 7 xy = 940 psi (figure part b). Determine the stresses acting on an element oriented at an angle = 55° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle 0. (a) PROBLEM 7.2-1 (b) 1175 psi Ţ 940 psi 7750 psi 7.2-5 The stresses acting on element A on the web of a train rail (see figure part a) are found to be 6500 psi tension in the horizontal direction and 18,500 psi com- pression in the vertical direction (see figure part b). Also, shear stresses with a magnitude of 3800 psi act in the directions shown. Determine the stresses acting on an element ori- ented at a counterclockwise angle of 30° from the horizontal. Show these stresses on a sketch of an ele- ment oriented at this angle. Cross Section (a) PROBLEM 7.2-5 B A Side View A (b) 18,500 psi 76500 psi 3800 psi
pru 7 Oy enüz žvaplanmadı Ot .00 üzerinden aretlenmiş Txy Soruyu aretle Ka Tnt Ox On (a) (b) On the surface of a structural member, stresses are given as ox=61 MPa, oy=32,7 MPa and Txy=-28,1 as shown in figure (a). Determine the maximum principal stress (MPa). Note: If the stress is compressive, use - sign. Yanıt:
7.2-5 The stresses acting on element A on the web of a train rail (see figure part a) are found to be 6500 psi tension in the horizontal direction and 18,500 psi com- pression in the vertical direction (see figure part b). Also, shear stresses with a magnitude of 3800 psi act in the directions shown. Determine the stresses acting on an element ori- ented at a counterclockwise angle of 30° from the horizontal. Show these stresses on a sketch of an ele- ment oriented at this angle. Can Stock Photo Inc./corepics Cross Section PROBLEM 7.2-5 Can Stock Photo Inc./scanrail A Side View Sa A 18,500 psi T (b) 16500 psi 3800 psi
10 KN 20 KN / m 5 KN / m A SIMPLE STRESSES 5 KN / m D 50 KN-m 5 KN / m F E 2. Points C and D of the 1.00 1.00 1.00 1.00 2.00 1.00 beam system shown in the figure is 500mm x 600 mm wooden (in meters) column. What is 30° 3.00 m bearing stress along the grain of the wooden post in Point C? 0.50 m
please help
5 Figure 5 shows a thick cylinder of 50 mm internal radius and 115 mm outer radius is subjected to an internal pressure of 60 MN/m² and an extemal pressure of 30 MN/m?. Determine the hoop and radial stresses at the inside and outside of the cylinder together with the longitudinal stress if the cylinder is assumed to have closed ends using analytical and graphical approaches.