The state of two dimensional stresses acting ona concrete lamina consists of a direct tensilestress sx%3DX,1.5 N/mm2, and shear stress,t = 1.2 N/mm?, which cause cracking of concrete.Then the tensile strength of the concrete inN/mm2 is(a)(c)1.50(b) 2.082.17(d) 2.29

major principal stress is the maximum tensile stress in concrete .

The state of two dimensional stresses acting on a concrete lamina consists of a direct tensile 1.5 N/mm2, and shear stress, t = 1.2 N/mm2, which cause cracking of concrete. stress s, = Then the tensile strength of the concrete in N/mm2 is (a) 1.50 (b) 2.08 (c) 2.17 (d) 2.29

The state of two dimensional stresses acting on a concrete lamina consists of a direct tensile 1.5 N/mm2, and shear stress, t = 1.2 N/mm2, which cause cracking of concrete. stress s, = Then the tensile strength of the concrete in N/mm2 is (a) 1.50 (b) 2.08 (c) 2.17 (d) 2.29

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter11: Fracture And Fatigue

Section: Chapter Questions

Problem 11.4P

See similar textbooks

Similar questions

> * The state of two-dimensional stresses acting on a concrete lamina consists of a direct tensile stress o. = 1.5 N/mm² and shear stress T = 1.20 N/mm², when cracking of concrete is just impending. The permissible tensile strength of the concrete is
pre stressed conc. solution pls answer
pre stressed conc. solution pls answer
The flexural strength (fr) of concrete measured from the bending test is always higherthan the direct tensile strength (ft). In reality, the stress in the cracked part of theconcrete is lower than ft. Also, failure may occur on the compressive side. Assuming1) there is no tension softening in the cracked zone, i.e., tensile stress stays at ft; and 2)infinitely large compressive strength, draw the stress distribution over the depth of thebeam at ultimate failure when the curvature of the section is approaching infinity. Withthis stress distribution, show that the upper bound of fr/ft is equal to 3. (Hint: On rotating the section, because the compressive stress can increase well beyondft, the neutral axis will continue to shift towards to the compression side.)
Please try to solve only part 2 within 20 minute This is request
Question -4.4
F 1. The "slump" test is used to determine the compressive strength of a concrete. (F) 2. For room temperature and axial loadingaluminum behaves as a brittle material. T. T 3. Proper curing is important for a concrete specimen to gain compressive strength. T. (F 4. Concrete usually has a good tensile strength. T F 5. The units of the modulus of elasticity are the same as for axial stress. T F 6. Plasticity is characterized by return of a ħaterial to original size & shape upon removal of stress. т F 7. Strain hardening increases the elastic strength of the material. T F 8. Some materials do not exhibit a well defined yield point. T F 9. The failure behavior of our aluminum specimen in our torsion test was expected. T F 10. Necking of a steel specimen loaded in tension is an example of Poisson's ratio.
Prob.5: A rectangular reinforced concrete beam has dimensions b = 300 mm, d = 530 mm and h = 600 mm, and is reinforced with 3 Ø32 mm bars. Materials strength are fe = 28 MPa, fy= 414 MPa. a) Find the moment that will produce the first cracking at the bottom surface of the beam basing your calculations on Ig. b) Determine the maximum stress in the steel and in the concrete under this Design of Reinforced Concrete Structures moment.
A reinforced concrete beam of rectangular section has the cross-sectional dimensions shown in the figure below. The concrete of normal density has a compressive strength of 30 MPa and a modulus of rupture of 3.3 MPa. The yield strength of steel is 400 MPa. a) Calculate the stress due to an applied bending moment of 45 kN-m b) Calculate the bending moment at which cracking of concrete will be initiated (cracking moment Mcr) h=600 mm b=300 mm 키 As-2000 mm 4- No 25 d=530 mm
At what percent of compressive strength of concrete the stress in beam changes from directly proportional to varying with respect to depth.
A composite beam is made of two brass [E = 99 GPa] plates bonded to an aluminum [E = 63 GPa] bar, as shown. The beam is subjected to a bending moment of 2210 N-m acting about the z axis. Assume b=44 mm, d1=28 mm, d2=13 mm. Determine:(a) the maximum bending stresses σbr, σal in the brass plates and the aluminum bar.(b) the stress in the brass σbrjσb⁢r⁢j at the joints where the two materials are bonded together.
PLS PROVIDE COMPLETE SOLUTION THANKS