2. A long steel pipe is subjected to a state of plane strain (ɛzz = Ezx = Ezy = 0) whenthe design loads are applied. At the critical point in the pipe, the non-zero stress143.28 MPa ,components are found to be oxx = 53.28 MPa , ơyyOxy40 MPa and o22 = 57 MPa . The material has a yield stress of= 245 MPa . Determine the factor of safety in the design based on the vonOyMises criteria.

Answered: Image /qna-images/answer/1bebba47-5b14-4bcd-ae4e-17c045c5caa8.jpg

2. A long steel pipe is subjected to a state of plane strain (8zz = Ezx = Ezy = 0) when the design loads are applied. At the critical point in the pipe, the non-zero stress 143.28 MPa , %3D components are found to be oxx = 53.28 MPa , ơyy Oxy 40 MPa and o22 = 57 MPa . The material has a yield stress of = 245 MPa . Determine the factor of safety in the design based on the von Oy Mises criteria.

2. A long steel pipe is subjected to a state of plane strain (8zz = Ezx = Ezy = 0) when the design loads are applied. At the critical point in the pipe, the non-zero stress 143.28 MPa , %3D components are found to be oxx = 53.28 MPa , ơyy Oxy 40 MPa and o22 = 57 MPa . The material has a yield stress of = 245 MPa . Determine the factor of safety in the design based on the von Oy Mises criteria.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. For each state of plane stress shown below, i.e., for configurations (a) and (b), indicate whether each component of the state of strain is: = 0 (equal to zero) >0 (greater than zero) <0 (less than zero) The material is linear elastic with Possion's ratio is between (0, 0.5), and the deformations are small. T 30 e X 0 Ex Ey Ez Yxy Yyz Yzx (a) (b) 1° (b) 1x
2. The Goodman diagram relates oa and om for fatigue failure after a specific number of cycles Nf, where da is the cyclic stress amplitude, and om the mean stress. For a steel specimen it is found that oa oa (0). [1- (om/OTS)] where Ors is the metal's tensile stress (375MPa), and oa (0)~0.450TS is the 107 cycle fatigue limit at zero mean stress. Assuming the specimen is cycled repeatedly between 0 stress and a peak stress, what is the maximum peak stress if failure in < 107 cycles is to be avoided? Ans: 233 MPa
A cylindrical specimen of 1018 steel having a diameter of 6.35 mm and a gauge length of38.1 mm is pulled in tension. Use the load-elongation characteristics tabulated below. Determine the yield strength (σy) at a strain offset of 0.002.
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 620 mm. The cross-sectional dimensions of the beam are b1 = 32 mm, d1 = 117 mm, b2 = 19 mm, d2 = 19 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 13 MPa, and the allowable compressive bending stress is 13 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 a M | A В
A critical point in a part made of a ductile material is subject to the following state of plane stress: 15ksi, 30 ksi, 15 ksi, Ox,min = -35 ksi, Oy,min = 30 ksi, Txy,min = -15 ksi. Ох,max бу,max Тxy,max %3D There are no stress concentrations. The load line is propositional. The material has a yield strength of Sy = 130 ksi, an ultimate strength of Su = 200 ksi, and a fully corrected endurance limit of Sn : 75 ksi. Calculate the: (a) Static factor of safety using the MSSTF, (b) Static factor of safety using the DETF, (c) Fatigue factor of safety using the Soderberg criterion, (d) Fatigue factor of safety using the Goodman criterion, (e) Fatigue factor of safety using the ASME elliptic criterion.
A steel bar 30 mm in diameter and 2 m long is encased in a shell of cast iron 5 mm thick. Compute the stress in each material, in MPa, if a compressive axial load of 150 kN is applied to the assembly. For steel, E = 200 MPa and for cast iron, E = 100 %3D GPa ( Select the correct response(s): 29.96 MPa 76.39 MPa 212.21 MPa 106.10 MPa 136.32 MPa 152.79 MPa 59.92 MPa 272.84 MPa
A steel component is subjected to alternate cyclical loading. The steel follows Basquin's law for high cycle fatigue, o, x N = C, (where the stress amplitude is in MPa). Ignore the geometric detail and assume that Marin's modifying factors are all equal to 1. You are given the minimum stress ain = -213 MPa, the maximum stress omax = 213 MPa. The material data are Tensile strength oUTS = 539 MPa, Basquin's constant c, = 875 MPa, Basquin's exponent a = 0.085. a) Calculate the stress ratio R, the stress amplitude o, in MPa and the mean stress am in MPa. The answers are acceptable with a tolerance of 0.01 for R and of 1 MPa the stresses. R: MPa MPа b) Calculate the corresponding life, in 10° cycles, (tolerance of 0.1 106 cycles) N :
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 760 mm. The cross-sectional dimensions of the beam are b1 = 33 mm, d1 = 110 mm, b2 = 20 mm, d2 = 20 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 11 MPa, and the allowable compressive bending stress is 12 MPa. Determine the largest moment M that can be applied as shown to the beam.
The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests, it has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑y 40 40 MPa 80 MPa 25 MPa ➜X
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 680 mm. The cross-sectional dimensions of the beam are b, = 36 mm, d1 = 95 mm, b2 = 22 mm, d2 = 22 mm, and a = 7 mm. For this material, the allowable tensile bending stress is 11 MPa, and the allowable compressive bending stress is 13 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 M d2 d1 |A В b1 Answer: M = N-m
If the material is machine steel having a yield stress of sY = 500 MPa, determine the factor of safety with respect to yielding if the maximum shear stress theory is considered.
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 580 mm. The cross-sectional dimensions of the beam are b1 = 33 mm, d1 = 112 mm, b2 = 20 mm, d2 = 20 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 15 MPa, and the allowable compressive bending stress is 13 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 a a M d2 A B bị