The composite bar shown in the figure is firmly attached to unyielding supports. An Axial force P = 52 kips is applied at 65°F. Compute the stress (ksi) in the Aluminum at 116 °F. Assume a = 6.5 x 10-6/° F for steel and 12.8 x 106/°F for aluminum Given: L1 = 15in; L2 = 11in Your final answer should contain two decimal places Steel A = 3 in² E = 29 x 106 psi Correct Answer: 3.92 L2 Aluminum A = 2 in² E = 10 x 106 psi L1

The composite bar shown in the figure is firmly attached to unyielding supports. An Axial force P = 52 kips is applied at 65°F. Compute the stress (ksi) in the Aluminum at 116 °F. Assume a = 6.5 x 10-6/° F for steel and 12.8 x 106/°F for aluminum Given: L1 = 15in; L2 = 11in Your final answer should contain two decimal places Steel A = 3 in² E = 29 x 106 psi Correct Answer: 3.92 L2 Aluminum A = 2 in² E = 10 x 106 psi L1

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Similar questions

Estimate the transverse tensile strength of the concrete in Problem 12.6.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
Please answer, Asap. Thank you.
! Required information A steel bar (Es= 210 GPa) and an aluminum bar (Ea = 70 GPa) are bonded together to form the composite bar shown. 8 mm 8 mm 8 mm Aluminum 24 mm -Steel Determine the maximum stress in steel when the bar is bent about a horizontal axis, with M= 56 N.m. The maximum stress in steel is - MPa.
Please provide complete solution and FBD in a bond paper (handwritten) for full credit.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
i need the answer quickly
Required information A steel bar (Es = 210 GPa) and an aluminum bar (Ea = 70 GPa) are bonded together to form the composite bar shown. 8 mm Steel 8 mm 8 mm Aluminum 24 mm Determine the maximum stress in aluminum when the bar is bent about a horizontal axis, with M= 66 N-m. The maximum stress in aluminum is MPа.
1. Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is % X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is o=20.0 ksi, the allowable shear stress for the rivets is o=25.0 ksi and the allowable bearing stress on the rivets and splice plates is o=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded? Splice Plates a-0.75 in Bar Lc =0.80 in. Bar P d = 1.0 in. b=4.0 in. Rivets 'e = 6.0 in.
The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading shown. Determine the displacement of end A with respect to end D and the normal stress in each section. The cross-sectional area and modulus of elasticity for each section are shown in the figure. Neglect the size of the collars at B and C. Steel Eg = 200 GPa Acp= 39 mm? Aluminum Соpper Eg = 70 GPa AAB= 58 mm? Ecu = 126 GPa ABc = 77 mm? 16 kN 8 kN 9 kN 7 kN 16 kN 8 kN – 450 mm- -300 mm- 400 mm-
The bar 1 consists of an aluminum cover and a brass core. The data is presented in the table. Determine: a. The maximum force P that can be applied at C. Answ: 84.22 kN. b. The deformation at the point where the load is applied. Answ: 1.5278 mm.