The state of stress at a given point in a material component is = 120 MPa ; 0₁= The loading on the component is increased so that stresses are increased to values which are k times the given values. Determine the maximum value of k if the material can withstand maximum normal and shear stresses of 300 MPa and 200 MPa respectively. = -80 MPa and t = 60 MPa

The state of stress at a given point in a material component is = 120 MPa ; 0₁= The loading on the component is increased so that stresses are increased to values which are k times the given values. Determine the maximum value of k if the material can withstand maximum normal and shear stresses of 300 MPa and 200 MPa respectively. = -80 MPa and t = 60 MPa

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.3P

See similar textbooks

Similar questions

3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 13.05 ksi, or in bronze of 100 MPа. Aluminum A = 400 mm? Bronze A = 200 mm Steel A = 500 mm? 2P 4D 2.5 m 2.0 m 1.5 m
Problems: Stress (ksi) 53.2 1. Determine the ductility (u) of the material based on the stress- strain diagram (problem S5.1). 43.6 37.1 0.0013 0.0063 0.163 0.247 Strain (in/in)
Q.3: A steel rod with a cross sectional area of 150 mm² is stretched between two fixed points. The tensile load at 20°C is 5000 N. a) What will be the stress at -20°C. b) At what temperature will the stress be zero? Assume a-11.7 μm/m . °C and E= 200 GPa?
Q 2: The state of stress at a point is characterized by the components: Ox Txy Txz [12 3 Tyx Oy Tyz = 4 [Tzx Tzy Oz 0 10. Find the values of the principal stresses and their directions?
Consider the state of stress as shown in figure. What will be the principal stresses? 02= 16Mpa oy= – 48 M pa, Try = 60 Mpa T 48 Mpa + 16 Mpa 60 Mpa
The stress concentration occurs whenever there is an abrupt change in the cross-section of a component or there is any discontinuity in the material. The figure given below shows a flat plate with a hole of diameter d. The plate is fixed at one end and the other end is subjected to a tensile load of P = 44 kN due to which there is a change in length of 0.4 mm. The thickness of the plate is 11.5 mm. The maximum stress developed in the flat plate is 228 MPa. Take Young's modulus(E) = 210 GPa and theoretical stress concentration factor =2, Calculate the following values: i) Width of the plate (W2) in mm ( ii) Nominal Stress in MPa ( iii) Diameter of the hole (d) in mm
2. For the state of stress shown, determine the range of value of for which the normal is equal to or less than 100 MPa and 50 MPa. stress x' + 90 MPa 60 MPa =
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are 0 = 100MPa, oy = 35 MPa, and Txy = 70MPa, acting in the directions shown in the figure. Oy Txy Ox
CIVIL ENGINEERING
At a point in a stressed material the stress components are: Ox= -30, Oyy = 75, 1 = 72, Tyz = 40, 0 = 110 T= 30, all are in MPa Calculate the normal, shear and resultant stresses on a plane whose normal makes an angle of 40° with the x axis and 60° with the y-axis.
The stress concentration occurs whenever there is an abrupt change in the cross-section of a component or there is any discontinuity in the material. The figure given below shows a flat plate with a hole of diameter d. The plate is fixed at one end and the other end is subjected to a tensile load of P = 41 kN due to which there is a change in length of 0.4 mm. The thickness of the plate is 11 mm. The maximum stress developed in the flat plate is 235 MPa. Take Young's modulus(E) = 210 GPa and theoretical stress concentration factor =2, Calculate the following values: i) Width of the plate (W2) in mm ii) Nominal Stress in MPa iii) Diameter of the hole (d) in mm Hole with stress concentration factor 2 35 mm W2 35 mm P 300 mm 350 mm- 250 mm
answer quickly