The state of stress at a given point in a material component is = 120 MPa ; Oy ox = -80 MPa and t = 60 MPa The loading on the component is increased so that stresses are increased to values which are k times the given values. Determine the maximum value of k if the material can withstand maximum normal and shear stresses of 300 MPa and 200 MPa respectively.

The state of stress at a given point in a material component is = 120 MPa ; Oy ox = -80 MPa and t = 60 MPa The loading on the component is increased so that stresses are increased to values which are k times the given values. Determine the maximum value of k if the material can withstand maximum normal and shear stresses of 300 MPa and 200 MPa respectively.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A homogenous isotropic material of size 20 cm x cm x 20 cm is placed inside a rigid box of internal dimension 20 x 20 x 20 cm. The top of the box is open and the material inside is subjected to a uniform compressive stress of 10 N/mm² from the top. Assuming there is no friction between the surface of contact, find the stresses on the side faces of the material. Also find maximum shear stress, the normal stresses on the plane of maximum shear stress and the change of volume of the material. Young's modulus E is 1 x 105 N/mm² and Poisson's ratio, m = 0.3 for the material. S 10 N/mm² 20 cm 20 cm-
Stress analysis
Stress (MPa) 2000 Using the stress-strain results shown in the figure, determine the 0.2% offset yield strength and the strain at the onset of necking. Indicate both on the graph and write the value along with units in the space provided. MPa 2000 1000 1000 0.000 0.005 0.010 0.015 Strain 0 0.000 0.020 0.040 0.060 0.080 Strain 100 300 Yield Strength units: 200 Stress (10³ psi) Strain at the onset of necking: units:
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are 0 = 100MPa, oy = 35 MPa, and Txy = 70MPa, acting in the directions shown in the figure. Oy Txy Ox
Quick
A 20 m long steel rod is at a temperature of 20°C. The rod is heated so that temperature rises by 50°C. If rod is allowed to expand by 14 mm, what will be the stress induced in rod? Take E = 200 GPa and a = 12 × 10-6/°C. (a) 20 MPa (c) 68 MPa (b) 35 MPa (d) None of these
Time len A material has the stress-strain behavior shown in the Figure below. Calculate the toughness (T) of this material. given that S1=195 Mpa; S2=243.75 Mpa; El=0.19; E2=0.38 E1 Strain E2 Stress - Strain diagram of a metal alloy OA.T= 18.52 Mpa O B.T= 92.62 Mpa O C.T= 37.05 Mpa O D.T= 60.21 Mpa Stress (Mpa) 3
Question: Principal stresses at a point are 80 N/mm2 and 40 N/mm² both tensile. The yield stress in simple tension for this material is 200 N/mm2 The values of factors of safety according to maximum principal stress theory and maximum shear stress theory, respectively, are
Q: A piece of material is subjected to tensile stress of 70 N/mm² in one direction and a compressive stress of 50 N/mm² in a direction at right angles to the previous one. Find fully the stresses on a plane the normal of which makes an angle of 40 degree with the 70 N/mm2 stress.
In a steel railroad, the 12 meters long rails are laid with a clearance of 5 mm at a temperature of 20 degrees centigrade. The modulus of elasticity of steel is 200 GPa. a) At what temperature will the rails just touch if the coefficient of linear expansion is 11.7x10^-6/°C.? b) Determine the stress in the rails at 65 °C
In a tensile test on a metal specimen having a cross section 20 mm by 10 mm elastic breakdown occurred at a load of 70 000 N. A thin plate madec from the same material is to be subjected to loading such that at a certain point in the plate the stresses are o,=-70 N/mm², 7.y= 60 N/mm² and o. Determine the maximum allowable values of o, using the Tresca and von Mises theories of elastic breakdown. Ans. 259 N/mm² (Tresca), 294 N/mm² (von Mises).
Theory of failure.