At a point in a strained material, tensile stress of 100 MPa and compressive stress of 60 MPa are found to be principal stresses Maximum shear stress at that point is: O 60 MPa O 20 MPa O 40 MPa O 80 MPa

At a point in a strained material, tensile stress of 100 MPa and compressive stress of 60 MPa are found to be principal stresses Maximum shear stress at that point is: O 60 MPa O 20 MPa O 40 MPa O 80 MPa

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.3P

See similar textbooks

Similar questions

Q3
At a point in an elastic material under strain, there are normal stresses of 60 N/mm2 and 40 N/mm2 (both tensile) at right angles to each other, with positive shearing stress of 20 N/mm2. The maximum shear stress and direction its plane will be respectively
The rectangular plate is subjected to the deformation shown by the dashed lines. Determine the followings: 1) the average normal strain along side AB 2) the average normal strain along the diagonal AC 3) the average normal strain along the diagonal BD 4) the shear strain at B 5) the shear strain at D B C 8P mm 2 mm 4 mm 10P mm
a. At a point in a given material the three dimensional state of stress is given by ox = oy oz = 10 MPa ,Txy F 20 MPa, Tyz = %3D !! TXZ = 10 MPa. Compute the principle planes if the corresponding principles stresses are, ol = 37.3 MPa, c2 = 10MPA, o3 =2.7 MPa %3D %3D b. , What no
A mild steel bar of square cross-section 40 mm x 40 mm is 400 mm long it is subjected to a longitudinal tensile stress of 440 N/mm² and lateral compressive stress is 200 N/mm² in perpendicular directions. E = 2 x 105 N/mm², μ = 0.3. What is the approximate elongation of the bar in the longitudinal direction?
A point in beam experiences a tensile stress (due to bending) of 50 N/mm2 and a shear stress of 20 N/mm2. The principal stresses are:
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D What is the axial stress o Ag in Pa? 10KN 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
Question 4 At a point in a material there are two direct stresses of 60 MPa tensile and 50 MPa compressive acting at right angles to each other. The greatest principal stress in the material is limited to 125 MPa in tension. What will be maximum shearing stress to which the material can be subjected on the given plane
At a point in elastic medium normal stresses in two mutually perpendicular directions are 120 MPa, 40 MPa (both tensile) associated with a tangential stress of 30 MPa. The principal stresses at the locations are
A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 με is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?
A small aluminum alloy [E = 62 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 185 mm. The cross-sectional dimensions of the tee shape are b = 22 mm, d = 33 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 400 με is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?
At a point in an elastic material there are two mutually perpendicular planes, one of which carries a direct tensile stress of 50 N/mm² and a shear stress of 40 N/mm² while the other plane is subjected to a direct compressive stress of 35 N/mm² and a complementary shear stress of 40 N/mm². Determine the principal stresses at the point, the position of the planes on which they act and the position of the planes on which there is no direct stress. Ans. o1 = 65.9 N/mm², 0 = -21.6°, o1=-50.9 N/mm², 0 = -111.6°. No direct stress on planes at 27.1° and 117.1° to the plane on which the 50 N/mm² stress acts.