The state of stresses in the x and y directions at a point in a given material is shown in the figure below. If the value of the shear stress in the x-y axes Ty is 19N/mm2, find themaximum direct stress that can be found at this point in any possible direction. Round off your answer to the nearest N/mm2.10 N/mm2Txy20 N/mm220 N/mm2Txy10 N/mm2

The state of stresses in the x and y directions at a point in a given material is shown in the figure below. If the value of the shear stress in the x-y axes T, is 19N/mm2, find maximum direct stress that can be found at this point in any possible direction. Round off your answer to the nearest N/mm?. 10 N/mm2 Txy 20 N/mm2 20 N/mm? Txy 10 N/mm2

The state of stresses in the x and y directions at a point in a given material is shown in the figure below. If the value of the shear stress in the x-y axes T, is 19N/mm2, find maximum direct stress that can be found at this point in any possible direction. Round off your answer to the nearest N/mm?. 10 N/mm2 Txy 20 N/mm2 20 N/mm? Txy 10 N/mm2

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.3P

See similar textbooks

Related questions

Q: Problem # 3: The steel bars are firmly attached to rigid supports. Initially the temperature is…

Q: If the angle of obliquity for the resultant stress at a plane which is 45° from the principal stress…

A: To find the ratio of stress in x-direction to stress in y-direction

Q: An aluminum right-circular cylinder surrounds a steel cylinder as shown in Fig. 1-29. The axial…

Q: 3. The stress element is shown in the figure. Determine the equivalent stress according to the third…

A: Solution: Given: σx=40 MPaσy= 40 MPaτxy=60 MPa Equivalent stress according to third and fourth…

Q: The figure below shows the cross-section of a beam that carries a vertical shear force, V= 72 kN.…

Q: 2.43.The distribution of stress in an aluminum machine component is given (in megapascals) by = y+…

Q: Wire BC has a diameter of 0.10 in. And its material has the stress-strain characteristics shown in…

A: Shear stress is the amount of loading which gets sheared in the beam or any structural element by…

Question

The state of stresses in the x and y directions at a point in a given material is shown in the figure below. If the value of the shear stress in the x-y axes Ty is 19N/mm2, find the
maximum direct stress that can be found at this point in any possible direction. Round off your answer to the nearest N/mm2.
10 N/mm2
Txy
20 N/mm2
20 N/mm2
Txy
10 N/mm2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Stresses in saturated soil without seepage

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The state of stresses in the x and y directions at a point in a given material is shown in the figure below. If the value of the shear stress in the x-y axes Ty is 17N/mm2, find the maximum shear stress that can be found at this point in any possible direction. Round off your answer to the nearest N/mm2. 10 N/mm2 Txy 20 N/mm2 20 N/mm2 Txy 10 N/mm2
The state of stresses in the x and y directions at a point in a given material is shown in the figure below. If the value of the shear stress in the x-y axes Ty is 11 N/mm², find the minimum direct stress that can be found at this point in any possible direction. Round off your answer to the nearest N/mm?. If the answer is negative do insert the "-" sign. 10 N/mm2 Txy 20 N/mm2 20 N/mm2 Ixy 10 N/mm2
Stress (MPa) 2000 Using the stress-strain results shown in the figure, determine the 0.2% offset yield strength and the strain at the onset of necking. Indicate both on the graph and write the value along with units in the space provided. MPa 2000 1000 1000 0.000 0.005 0.010 0.015 Strain 0 0.000 0.020 0.040 0.060 0.080 Strain 100 300 Yield Strength units: 200 Stress (10³ psi) Strain at the onset of necking: units:
2. For the state of stress shown, determine the range of value of for which the normal is equal to or less than 100 MPa and 50 MPa. stress x' + 90 MPa 60 MPa =
1.16 The stress-strain relationship shown in Figure P1.16 was obtained during the tensile test of an aluminum alloy specimen. 60,000 H Stress, psi 40,000 20,000 0 Figure P1.16 0.002 0.004 0.006 0.008 Strain, in./in. Determine the following: a. Young's modulus within the linear portion. b. Tangent modulus at a stress of 45,000 psi c. Yield stress using an offset of 0.002 strain d. If the yield stress in part c is considered failure stress, what is the maximum working stress to be applied to this material if a factor of safety of 1.5 is used? 4
Draw the three Mohr's circles that describe the state of stress in (Figure 1). Figure 1 of 1 > 25 ksi 25 ksi
3 - A strain gauge is attached to the side of a beam, as shown by the cross-section view in the figure. When the beam is subjected to a specified uniform moment, the longitudinal strain measured by the gauge is -300μ. Plot the axial stress profile over the height of the cross- section. What is the magnitude of the moment that produced this strain gauge reading? Assume E = 75 GPa. 10↑ Strain gauge dimensions in mm 30 30 beamcross-section
Q.3: A steel rod with a cross sectional area of 150 mm² is stretched between two fixed points. The tensile load at 20°C is 5000 N. a) What will be the stress at -20°C. b) At what temperature will the stress be zero? Assume a-11.7 μm/m . °C and E= 200 GPa?
SOM 3.1 Show your complete/correct solution. ( I need detailed solution since there is given answer.) Given answer: Stress in bars AC = 49468.962 psi Stress in bars CB = 8588.361 psi
If the angle of obliquity for the resultant stress at a plane which is 45° from the principal stress is 30° as shown in the figure then find the ratio of stress in x-direction to stress in y-direction. A-3.73 B 3.73 C 1.73 6² D 0.268 Correct Option B # 45%
The rectangular plate is subjected to force P that causes elongation in the horizontal direction and shrinking in the vertical direction as shown with the dashed line in the figure. Assume a = 550 mm, Δx = 2 mm, and Δy = 1.1 mm. What is the normal strain in the y-direction? What is the normal strain in the n-direction?in micro£
Q3 / An element in plane stress at the surface of a large machine is subjected to stresses shown below. Using Mohr's circle determine the following quantities (a) the principal stresses and their directions and (b) the maximum shearing stresses and the directions of the planes on which they occur. 100 MPa 50 MPa 75 MPa 75 MPa 50 MPa 100 MPa