The spur gear arrangement shown in the figure has a pinion (diver Gear A) that rotates at 625 rpm, an idler Gear B and a driven gear (Gear C). The gears have a module of 5 mm and a pressure angle of 20 degrees. Given the number of teeth as shown in the figure, determine: i) ii) iii) The pitch diameters of each of the gears. The torque that each shaft is required to transmit. The forces on each of the gears

The spur gear arrangement shown in the figure has a pinion (diver Gear A) that rotates at 625 rpm, an idler Gear B and a driven gear (Gear C). The gears have a module of 5 mm and a pressure angle of 20 degrees. Given the number of teeth as shown in the figure, determine: i) ii) iii) The pitch diameters of each of the gears. The torque that each shaft is required to transmit. The forces on each of the gears

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A…

Q: C) : A compound gear train shown in figure consists of a driver gear A engaging with gear B.…

Q: Straight bevel gear Input shaft C2: Helical gears D Spur gears E 3 Inputs: Power= 11 kW Speed- 2900…

Q: (B) Two shafts A (driver) and B (driven) in the same straight line are geared together through an…

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

A: Pressure angle is 20 degreeNumber of teeth on pinion is 24Number of teeth on gear is 96Pinion…

Q: State an equation tha relate the number of teeth of gear D, B and C.

Q: calculate the indexing for the following: 1. 1623 divisions 2. 1124 divisions

A: Given DataDivisionsN=16232-N=1124 three plates

Q: (B) The sun and plant gear of an epicyclical shown in figure below the annular gear D has 100…

Q: 1

A: Given data 1. Number of teeth on Z1=15 2. Number of teeth on Z2=31 3. Number of teeth on Z3=17…

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

Q: A gear train is composed of four helical gears with the three shaft axes in a single plane, as shown…

Q: In the figure below, Gears B and C represent a compound gear and have the following details. The…

A: number of teeth t A=100 tB=40 tc=80 tD=20 input torque Ti=42 Nm speed of gear A NA=2400 rev/min…

Q: 6. Two mating spur gears have 40 and 120 teeth respectively. The pinion rotates at 1200 rpm and…

A: Given that, Two spur gear of 40 teeth and 120 teeth Pinion rotates at 1200 rpm Torque is 20 N.m

Q: Gear 2 (pinion) runs at 1800 rpm ccw and transmits 3.5 kW to frictionless, idler gear 3. The…

Q: A 84-tooth gear is driven by a 17-tooth spur pinion. The diametral pitch is 32 teeth/in and the…

A: Given: Number of teeth on the pinion (Tp)=17 Number of teeth on the gear (TG)=84 Diametral Pitch…

Q: nning at 100 rpm clockwise. B is an output shaft running at 250 rpm clockwise. Torque on A i

A: given:NA=100RPMNB=250RPMTA=50KN-m

Q: A pair of parallel helical gears consists of a 20 teeth pinion mashing with a 40 teeth gear. The…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: The figure shows a schematic representation of a gear system. The gears are meshed with one another…

Q: a left-hand helix angle of 35°, a normal pressure angle of 26°, and a normal module of 3 mm. Find:…

A: (a) Write the given data. No. of tooth on pinion, Z1=15No. of tooth on gear, Z2=37α=35°ϕn=26°mn=3 mm

Q: The below mentioned simple gear train is used to transfer 17kW power at 750 rpm.The module of the…

A: Given, m= 5mm, Tq =20, Tr = 60 and Ts = 30

Q: A power of 25 KW is transmitted by a pair of spur gears. Pressure angle= 20, radial force generated…

A: Given, P = 25 kW, θ = 20 0, Fr = 220 daN = 2200 N, N = 600 N, t = 33, Dp2 / Dp1 = 3 We need to find…

Q: For the gear train shown in the figure. Planet gears 3, 4, and 5 are rigidly connected to a common…

A: The speed of gear 1 is 30 rpmN1=10N3=24N4=N5=12N6=10N7=30we need to determine speed of the gear 7…

Q: Q1 Two spur gears in a simple train shown in Figure Q1 are having the same module, m = 2 and their…

Q: Two parallel shafts, about 550 mm apart are to be connected by spur gears. One shaft is to run at…

Q: (Pinion) Gear 2 Idler N2 = 75 teeth Gear 3 Output N3 = 25 teeth O teeth he following: 1. Pinion…

Q: 50 teeth A 90⁰ B 80 teeth C 60 teeth

A: Given, NA= 700 rpm

Q: The shaft from a DC motor is connected to gear A which rotates at 45rps in clockwise direction.…

Q: Gear 1 has a module of 4 mm/tooth and 25 teeth. This gear drives Gear 2 whose speed is 410 rpm. The…

A: The module of gear 1 is m1=4 mm/tooth. The number of teeth on gear 1 is T1=25. The speed of gear 2…

Q: A two-stage gear train consists of four gears meshed together (Figure 10). The secondand third gears…

A: for the given gear train To determine angular velocity of gear 4 in terms of ω1,n1,n2,n3 and n4

Q: rpm of D in the clockwise direction is

A: Figure shows the epicyclic gear train.For this data is given as: Number of teeth on the gears;…

Q: Problem : A train of spur gears with 20°full-depth involute teeth is shown in the Figure below. Gear…

A: Here Given Power P=5000 WattN1=720 rpmT1=20T2=50T3=30T4=60m=4mmϕ=20°Radius of…

Q: Objective: Dimensional comparison between straight tooth gears and helical cylindrical gears.…

Q: Q(1): For the component epicyclic gear train shown in the figure, the number of teeth of gears (A, B…

A: Given diagram:

Q: Question 1 A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4…

Q: Two internal 10-pitch, 20° full-depth gears are used in a system. The pinion has 28 teeth and the…

A: Given Data The number of teeth on pinion is:t1=28 The number of teeth on the gear is:t2=70 The…

Q: 20° pressure angle. Gear 3 is an idler (b) Find the torque T4c that gear 4 exerts on shaft c.

A: Calculate the speed of the shaft in rad/sec. Here, the speed of the shaft in rev/min is .…

Q: You have been asked by your engineering company to design a complete gear and shaft system shaft…

A: Given:- TA=15 kN-m(clockwise direction),TB=30 kN-m(clockwise direction),TC=75 kN-m(anti-clockwise…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

The spur gear arrangement shown in the figure has a pinion (diver Gear A) that rotates at 625 rpm, an
idler Gear B and a driven gear (Gear C). The gears have a module of 5 mm and a pressure angle of 20
degrees. Given the number of teeth as shown in the figure, determine:
i)
ii)
iii)
The pitch diameters of each of the gears.
The torque that each shaft is required to transmit.
The forces on each of the gears
40 teeth
TIT
A
-90⁰
tmt
B
70 teeth
50 teeth

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Evaluate pitch diameter.

VIEW

Step 3: Evaluate angular speeds of remaining shafts.

VIEW

Step 4: Evaluate torques transmitted by each shaft.

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 29 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

please help
Problem 2. A compound gear train as shown in the following figure, Gear 1 has 24 teeth and Gear teeth of diametral pitch of 4. Gear 3 has 30 teeth and Gear 4 has 50 teeth of diametral pitch of 3. Gear 1 turns 12 rpm in clockwise direction. 2 has 70 (a) Computer the speed and direction of the shaft carrying Gear 4. (b) Find the torque at Shaft c if the input horsepower at Shaft a is 50? Shaft b Shaft c Shaft a Gear 1 Gear 2 Gear 3 Gear 4
An epicyclic gear shown in Figure 1 consists of ring gear, planet gear and sun gear. The ring gear has 72 internal teeth and sun gear has 32 external teeth. Planet gear meshes with both ring and sun gears and is carried on an arm which rotates about the centre of the ring gear at 20 r.p.m. If the gear A is fixed, Calculate the speed of plane gear.
Question 1: Gears The lath machine in the Central University of Technology (CUT) mechanicalworkshop uses epicyclic gear train shown in Figure 1 to operate. Plate gear C of this gear system are carried on the arm A and free to rotated. the pitch circle diameter of the internally toothed ring gear D is to be 214 mm and the module 4 mm. When the ring gear D is stationary, the arm A, which carries three planet wheels C of equal size, is to make one revolution in the same direction as the sun wheel B for every five revolutions of the driving spindle carrying the sunwheel B Figure 1 attached 1.1. Calculate the number of teeth of the ring gear D. 1.2. State an equation tha relate the number of teeth of gear D, B and C. 1.3. Use the table method to calculate the number of teeth of gear B. 1.4. Calculate the number of teeth for gear C.
Name: Referring to the given figure, spur gear A receives 5 hp at 650 rpm through its shaft and rotates clockwise. Gear B is an idler and gear C is the driven gear. The pressure angle o is 20° and the gear diameters: DA, DB, and DC are 6", 12", and 9" respectively. Determine: a. The torque each shaft must transmit, b. The tooth load for which each gear must be designed (Fr and Ft), C. The force applied to the idler shaft as a result of the gear tooth loads. C
Please use the following table and please the ratio is not 1.714 this answer is wrong. Please don’t reply with same answered way previously!!!!
For two standard 25 degrees full-depth involute gears with velocity ratio 0.5 and module 8mm. The pinion gear of 100 mm diameter is transmitting a power of 4 kw to the gear. Given that the pinion rotates in the counterclockwise direction at 150 rpm. Determine: a) The clearance. b) The whole depth. c) Dedendum. d) The diameter and rotational speed of the driven gear. e) Whether the gear interfere with the pinion. f) The forces on each of the gears and show on a free body diagram.
plz solve 4 and 5 where X = 5
Please help
An epicyclic gear shown in figure below consists of ring gear, planet gear and sun gear. The ring gear has 72 internal teeth and sun gear has 32 external teeth. Planet gear meshes with both ring and sun gears and is carried on an arm which rotates about the centre of the ring gear at 20 r.p.m. If the gear A is fixed, Calculate the speed of plane gear.
In a gear set, a 36-tooth spur pinion drives a 60-tooth spur gear. The teeth of these gear are cast iron profile. The diametral pitch is 6-teeth/in, the face width si 0.5 inches, and the pressure angle is 20 degrees. Assume that the pinion transmits 10 hp at a speed of 2000 rpm. Find the pitch diameters of the gears. Find the pitch line velocity in ft/min Find the velocity factor Ky Find the tangential load in lbf Find the contact stress in kpsi, assuming CP=1960 psi.
For the gear train below, th numbers of teeth for individual gears are 12 9gear #1), Gear 18 (gear #2), 14 (gear #3), and 18(gear #4), To obtain a counter-clockwise rotation of 1500 rpm for the output gear(#4). What should be the rotation speed of the input gear (#1) and in which directions should the input gear rotate