The spherical gas tank is fabricated by bolting together two hemispherical thin shells of thickness 30 mm. The gas contained in the tank is under a gauge pressure of 2.5 MPa. If the tank has an inner diameter of 8 m and is sealed with 900 bolts each 20 mm in diameter, determine the normal stress developed in the wall of the tank.

The spherical gas tank is fabricated by bolting together two hemispherical thin shells of thickness 30 mm. The gas contained in the tank is under a gauge pressure of 2.5 MPa. If the tank has an inner diameter of 8 m and is sealed with 900 bolts each 20 mm in diameter, determine the normal stress developed in the wall of the tank.

Name: The spherical gas tank is fabricated by bolting together twohemispher
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The spherical gas tank is fabricated by bolting together twohemispherical thin shells of thickness 30 mm. The gas contained in thetank is under a gauge pressure of 2.5 MPa. If the tank has an innerdiameter of 8 m and is sealed with 900 bolts each 20

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At a temperature of 32.98 °C a 0.41-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 131.06°C, determine the magnitude of the normal stress (in MPa) in the steel rod if L = 332.28 mm and M = 209 mm.
A boiler is constructed of 8-mm-thick steel plates that are fastened together at their ends using a butt joint consisting of two 8-mm cover plates and rivets having a diameter of 10 mm and spaced 50 mm apart as shown. If the steam pressure in the boiler is 1.35 MPa, determine (a) the circumferential stress in the boiler’s plate away from the seam, (b) the circumferential stress in the outer cover plate along the rivet line a–a, and (c) the shear stress in the rivets.
The gas pipeline is supported every 20 ft by concrete piers and also lays on the ground. If there are rigid retainers at the piers that hold the pipe fixed, determine the longitudinal and hoop stress in the pipe if the temperature rises 60° F from the temperature at which it was installed. The gas within the pipe is at a pressure of 600 lb>in2. The pipe has an inner diameter of 20 in. and thickness of 0.25 in. The material is A-36 steel.
The pressure tank shown has an outside diameter of 100 mm and a wall thickness of 10 mm. Determine the absolute maximum shear stress at point H on the inner surface if the internal gauge pressure is 1.25 MPa and the applied torque is 375N•m. Show the stress state in matrix form and calculate eigenvalues.
The pressure vessel has a thickness 2 cm, diameter 20 cm. Calculate the internal pressure longitudinally and laterally. If the longitudinal stress is limited to 150 MPa and the circumferential stress is limited to 100 MPa. Which one will be used for safety? *
A spherical gas tank has an inner radius of r = 1.5 m. If it is subjected to an internal pressure of p = 420 kPa, determine its minimum required thickness if the maximum normal stress is not to exceed 12 MPa.
The assembly consists of a bronze tube fitted over a threaded steel bolt. The nut on the bolt is turned until it is finger-tight. Determine the stresses in the sleeve and bolt when the temperature of the assembly is increased by 200°F. Use the following data: Bronze Steel A (in. ²) 1.5 0.75 a (/°F) 10 × 10-6 6.5 x 10-6 Bronze tube 40 in. E (psi) 12 × 106 29 × 106 STA UT TEO
A steel cable having a diameter of 0.4 in. wraps over a drum and is used to lower an elevator having a weight of 800 lb. The elevator is 150 ft below the drum and is descending at the constant rate of 3 ft>s when the drum suddenly stops. Determine the maximum stress developed in the cable when this occurs. Est = 29(103) ksi, sY = 50 ksi.
The spherical pressure hull of the undersea submarine, under a research study shown in the figure below, has a 1 meter radius with a shell thickness of 30mm. The pressure hull is made of steel having a yield point of 700 MPa. Consider sea water to have a constant specific weight of 10kN/m³. Determine the depth pressure of submergence that would setup the yield point stress in the spherical shell. Use:p = yy, where y is the depth r = 1m t = 30mm comex
A steel cable having a diameter of 0.4 in. wraps over a drum and is used to lower an elevator having a weight of 800 lb. The elevator is 150 ft below the drum and is descending at the constant rate of 2 ft>s when the drum suddenly stops. Determine the maximum stress developed in the cable when this occurs. Est = 29(103) ksi, sY = 50 ksi.
A spherical rubber balloon is blown up until its diameter is three times the initial diameter. If E = 10750 psi and v=0.46, determine the stresses in the balloon. Assume the stress-strain behavior is linear. Answer: 0 = i ksi
Mechanics of materials II