The solid 37 mm diameter steel [E -200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (a) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P = 900 N, Q- 1100 N, LAB - 550 mm, LBC - 750 mm, LCD = 750 mm. B LAB LBC LCD V P Ve Part 1 Calculate the area moment of inertia for the solid circular cross-section. Answer: mm4

The solid 37 mm diameter steel [E -200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (a) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P = 900 N, Q- 1100 N, LAB - 550 mm, LBC - 750 mm, LCD = 750 mm. B LAB LBC LCD V P Ve Part 1 Calculate the area moment of inertia for the solid circular cross-section. Answer: mm4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A bar AB is attached at A as fixed support. A small spaces can be seen on the other side of the bar prior to another rigid surface. Load P is applied on the bar located at two-thirds of length L from point A. Determine the small space s if the support reactions at A and B are to be equal due to the external load P. See all necessary parameters below. L A E P A 3 m 2500 mm² GPa 45 77 KN 2/3 -L 113 mm -L ANSWERS: ALL ANSWERS SHOULD BE IN THREE (3) DECIMAL PLACES INCLUDING ZEROS 01 (delta due to external load P) = 52 (delta due to Reaction at B) = Small Space s = mm S₁ mm B
The solid 34 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. For the loading shown, determine: (a) the shaft deflection at pulley B. (b) the shaft deflection at pulley C. Assume P = 810 N, Q = 480 N, LAB = 260 mm, LBC = 400 mm
E 10-59. The A-36 hollow steel shaft is 2 m long and has an outer diameter of 40 mm. When it is rotating at 80 rad/s, it transmits 32 kW of power from the engine E to the generator G. Determine the smallest thickness of the shaft if the allowable shear stress is 7allow = 140 MPa and the shaft is restricted not to twist more than 0.05 rad.
The hand brake for a bicycle is shown. Portions DE and FG are free to rotate on bolt A which is screwed into the frame BC of the bicycle. The brake is actuated by a shielded cable where T1 is applied to point E and T2 is applied to point G. A spring having 60 N compressive force is placed between points E and G so that the brake stays open when it is not being used. Assume the change in the spring's force is negligible when the brake is actuated to produce the forces P = 350 N at points D and F. cable T2 spring o ma (a) Determine the necessary cable force (N) T2. (a) 348.33 (b) 526.67 (c) 545.25 (d) 421.01 80 mm (c) Determine the force (N) exerted by FG on bolt A. (a) 481.33 (b) 703.78 (c) 651.79 (d) 430.48
Answer the problem below, following the GIVEN-REQUIRED-SOLUTION format. Please provide the FBD. Problem: The pin spanner is used to turn shafts and collars. If a moment of is required to turn the 200-mm-diameter collar about its center O under the action of the applied force P, determine the contact force R on the smooth surface at A. Engagement of the pin at B may be considered to occur at the periphery of the collar.
Task 12 Z A C B 2a a a The figure above shows a static indeterminate beam ABCD. The beam has a fixed joint bearing in A and a sliding bearing in B and C. Note that the beam is continuous at point B and that the joint in the bearing is below the beam. The beam is subjected to an evenly distributed load q between A and C, while there is a point load F at point D. The beam is made of steel with an E-module E = 210 000 MPa and has a cross section with a second area moment ly = 12x106 mm4. The value of the evenly distributed load q and the length a are determined from: 9= ID+25 20 kN/m ID+40 a= m 50 ID=40 a) Determine how much the maximum force can be when the bearing in point B can withstand a maximum vertical force of 50 kN (Bz< 50 kN). Write your candidate number on all the sheets you upload. b) Now set the force F to the value you found in question a) and decide how big the deflection of the beam will be in point D, under the point load F. Write your candidate number on all the sheets…
The rigid bar AD (figure STR-4) is supported by two steel wires of 1.5mm diameter (E = 200 GPa) and a pin and bracket at D. Knowing that the wires were initially taut. Determine the following: a. The additional tension in wire BE when a load P=900 N is applied at D. b. The additional stress in wire FC when a load P = 900 N is applied at D c. The corresponding deflection at point D.
Determine the clamping force on the board A if the screw is tightened with a torque of M = 8 N ⋅ m. The square-threaded screw has a mean radius of 10 mm and a lead of 3 mm, and the coefficient of static friction is μs = 0.35.
4-5 The A-36 steel rod is subjected to the loading shown. If the cross-sectional area of the rod is 60 mm², determine the displacement of B and A. Neglect the size of the cou- plings at B, C, and D. 60° 3.30 KN 2 kN D C B A 8 kN 60⁰ 3.30 KN 0.75 m 1.50 m 0.50 m 2 kN
. Determine the magnitude of the moment of the 600-N force acting on the bracket shown. Expressyour un answer in Nm.
The solid 34 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (a) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P = 800 N, Q = 1100 N, LAB = 450 mm, LBC = 750 mm, LCD = 750 mm.
A solid 1.00-in.-diameter steel [G = 12000 ksi] shaft is subjected to the torques shown. Determine the rotation angle of pulley D with respect to the support at A. (1) 240 lb-ft 36 in. O-0.0653 rad O-0.0513 rad O-0.0415 rad O-0.0542 rad O-0.0316 rad B (2) 36 in. 215 lb-ft (3) 36 in. 110 lb-ft D