The hand brake for a bicycle is shown. Portions DE and FG are free to rotate onbolt A which is screwed into the frame BC of the bicycle. The brake is actuatedby a shielded cable where T1 is applied to point E and T2 is applied to point G.A spring having 60 N compressive force is placed between points E and G sothat the brake stays open when it is not being used. Assume the change in thespring's force is negligible when the brake is actuated to produce the forces P =350 N at points D and F.cableT2springo ma(a) Determine the necessary cable force (N) T2.(a) 348.33(b) 526.67(c) 545.25(d) 421.0180 mm(c) Determine the force (N) exerted by FG on bolt A.(a) 481.33(b) 703.78(c) 651.79(d) 430.48

A bicycle's hand brake is depicted. On bolt A, which is fastened into the bicycle's frame BC,…

The hand brake for a bicycle is shown. Portions DE and FG are free to rot bolt A which is screwed into the frame BC of the bicycle. The brake is actu by a shielded cable where T1 is applied to point E and T2 is applied to poi A spring having 60 N compressive force is placed between points E and G that the brake stays open when it is not being used. Assume the change i spring's force is negligible when the brake is actuated to produce the ford 350 N at points D and F. (a) Determine the necessary cable force (N) T2. (a) 348.33 (b) 526.67 (c) 545.25 (d) 421.01 (c) Determine the force (N) exerted by FG on bolt A. (a) 481.33 (c) 651.79 d) 430 49

The hand brake for a bicycle is shown. Portions DE and FG are free to rot bolt A which is screwed into the frame BC of the bicycle. The brake is actu by a shielded cable where T1 is applied to point E and T2 is applied to poi A spring having 60 N compressive force is placed between points E and G that the brake stays open when it is not being used. Assume the change i spring's force is negligible when the brake is actuated to produce the ford 350 N at points D and F. (a) Determine the necessary cable force (N) T2. (a) 348.33 (b) 526.67 (c) 545.25 (d) 421.01 (c) Determine the force (N) exerted by FG on bolt A. (a) 481.33 (c) 651.79 d) 430 49

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The compound beam is pin supported at C and supported by a roller at A and B. Note that there is a hinge at D. Find the reactions at the supports. Neglecting the thickness of the beam. (Provide the whole solution along with its FBD)
The change in diameter of the large steel bolt is carefully measured as the nut is tightened. Knowing that the initial diameter d = 50 mm, E = 190 GPa, and ? = 0.27, determine the internal force in the bolt if the diameter is observed to decrease by 0.009 mm after the nut has been tightened. Assume that the supports shown are fixed and rigid. d
Note:hand written solution should ne avoided.
C4 please help me with the answer and full solution
Which of the following statements is correct about the given structure? A В C E pin fixed roller fixed It is a determinate structure. O It is indeterminate to 4 degrees. It is indeterminate to 5 degrees. O It is indeterminate to 3 degrees .
write the solution clearly i will give like else dislike.
PLEASE DRAW AND LABEL PROPERLY THE FBD. THANK YOU. From the frame loaded as shown. Solve the following: a. Reaction at column A.b. Moment at column A.c. Force at member GH.d. Force at member FE.e. Force at memeber FH.
Please complete solution
will thumbs up if correct!
Which of the following statements is correct about the given structure? A В D E r pin fixed roller fixed It is a determinate structure. It is indeterminate to 4 degrees. It is indeterminate to 5 degrees. It is indeterminate to 3 degrees.
Q-A hollow cylinder with outer diameter 350 mm and thickness 20 mm is subjected to eccentric loading such that no tension is developed anywhere in the cross section. The maximum distance from the centre the load can be applied is mm.