The rigid bar ABC is suspended from three wires of the same material. The cross- sectional area of the wire at B is equal to half of the cross-sectional area of the wires at A and C. Determine the tension in each wire caused by the load P shown. A L DB P

The rigid bar ABC is suspended from three wires of the same material. The cross- sectional area of the wire at B is equal to half of the cross-sectional area of the wires at A and C. Determine the tension in each wire caused by the load P shown. A L DB P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The uniform bars AB and BC are connected with a pin at B and placed on a horizontal surface. The coefficient of static friction between the bars and the surface is µs = 0.85 . Find the force at A and reaction at B?
D 200 mm 300 mm - 400 mm- A C When force Pis applied to the rigid arm ABC, point B displaces vertically downward through a distance of 0.2mm. Determine the normal strain developed in wire CD.
Determine the length L of the center portion of the rectangular bar so that the maximum bending stress at A, B and C is the same. The bar has a thickness of 10 mm. 40mm ↓ 200mm 350N 60mm A C L/2 L/2 B 40mm 200mm
The rope AB exerts a 46 - N force T on the collar at A Let rCA be the position vector from point C to point A (Figure 1) Figure
Determine the shear lag factor of the connection shown in the figure.
4 decimal places
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 110 GPa] with a cross-sectional area of A₁ = 630 mm². Bar (2) is an aluminum alloy [E = 79 GPa] with a cross-sectional area of A₂ = 340 mm². A concentrated load of P = 52 kN acts on the structure at D. Assume L₁=910 mm., L₂=430 mm., a=450 mm., b=280 mm., and c=1030 mm. Determine: (a) the normal stresses 0₁, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. a 5 Answers: (a) 6₁ (b) VD= = tel i (1) L₁ L2 B C MPa, 0₂ = mm. i MPa
A cantilever beam (member AC) is supported with a column (member CD). Force P is applied to Point B, which is located at the midspan of the beam AC. The column is required to prevent excessive deflection of the beam as shown below. Determine the ratio of internal force in the column (member CD) to the critical buckling load of the column (Pcr). The length for both of the members, L, is 1,650 mm. The applied force, P, is 240 kN. The flexural rigidity for the beam and the column, EI, is 4.0X107 kN·mm2.
В A B C The system above is comprised of two-force members AB and AC, supporting a vertical force at point A. Assuming the system is drawn to scale and is in equilibrium, which of the following best describes the nature of the forces in members AB and AC? a) AB is in tension AC is in compression b) AB is in compression AC is in compression c) AB is in tension AC is in tension d) AB is in compression AC is in tension
A 13-mm-diameter steel (E = 193 GPa) rod (2) is connected to a 27-mm-wide by 10-mm-thick rectangular aluminum (E = 72 GPa) bar (1), as shown. Assume L1 = 0.74 m and L2 = 1.38 m. Determine the force P (in kN rounded to the nearest tenths) required to stretch the assembly 8.1 mm.
The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the pin B through an angle of 2°. Calculate the average normal strain developed in each wire. The wires are unstretched when the lever is in the horizontal position. A T 200 mm 200 mm B -300 mm- 200 mm D 300 mm E
Determine the force in member FG (assume FG is tension) of the truss shown in the figure below?. Set P = 671 lb. 2P 12h 12 12 12 Answer: