The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the pin B through an angle of 2°. Calculate the average normal strain developed in each wire. The wires are unstretched when the lever is in the horizontal position. 200 mm 200 mm H G -300 mm- 200 mm 300 mm D E

The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the pin B through an angle of 2°. Calculate the average normal strain developed in each wire. The wires are unstretched when the lever is in the horizontal position. 200 mm 200 mm H G -300 mm- 200 mm 300 mm D E

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3/98 Each of the three uniform 1200-mm bars has a mass of 20 kg. The bars are welded together into the configura- tion shown and suspended by three vertical wires. Bars AB and BC lie in the horizontal x-y plane, and the third bar lies in a plane parallel to the x-z plane. Compute the tension in each wire. B 600 mm 1200 mm A 30⁰! 1200 mm PROBLEM 3/98 600 mm -y
Question #4: Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. For the loading shown and knowing that Es = 200 GPa and Eb = 105 GPa, determine (dsteeF 40 mm, dbrass = 30 mm) 1- The reactions at A and E. 2- The deflection at C. 180 B 120 * 60kN 100 100 40 RN D Steel Brass Dimensions in mm.
1) DETERMINE TENSILE BENDING THE CROSS-SECTION BELOW. SOKN 20KN/m 3m THE MAXimum STRESSES OF THE B 30 кн/т Gm COMPRESSIVE Ано THE BEAM BEAM GIVEN 150MM SHOWIN 30mm 180mm 30mm
The homogeneous wire ABCD is bent as shown and is attached to a hinge at C. The length BCindicated by b is 94 mm. Determine the length L for which portion BDC of the wire is horizontal. L В IC 60 mm A The length L for which portion BCD of the wire is horizontal is mm.
4 Determine the design angle 8 for connecting mem- ber A to the plate if the resultant force is to be directed vertically upward. Also, what is the magnitude of the re- sultant? F₁ = 500 N -00 00 y ooo B FB = 400 N X
In this what to do?
Three wires supporting the stiff bar ABC is made from the same material. Wire at B has a cross-sectional area which is equal to half the cross-sectional area of the other two wires. Calculate the axial force exerted by the three wires.
Problem 12 A plate is fastened to a fixed member by four 16mmP rivets arranged as shown. Compute the maximum shearing stress developed in the rivets. 30KN 100mm spacing 30KN
If the load P on the beam causes the end C to be displaced 10 mm downward, determine the normal strain in wires CE and BD.
490 mm 200 mm 640 N B 480 mm 160 mm 240 mm PROBLEM 4.152 The pipe ACDE is supported by ball-and-socket joints at A and E and by the wire DF. Determine the tension in the wire when a 640-N load is applied at B as shown.
9. pls answer...
The rigid beam is supported by a pin support at A and steel wires BD and CE (E-200GPA). The steel wires are 1cm in diameter. If the load P is 5kN and the weight of the beam is neglected, solve the deformation at wire BD. E 4 m +2m+2m -3 m O 0.417mm O 0.497mm O 0.329mm O 0.231mm