Q The mechanical system, shown in the figure, consists of two identical steel rods (A 60 mm?, E= 200 GPa, a 12 x 10/ °C) and a "rigid" beam AC. The beam is supported by a smooth pin at B. The nuts at A and Care initially tightened just enough to remove the slack, leaving the two rods stress-free. Determine the axial stresses induced in rods (1) and (2) if the temperature of both rods is decreased by 60 °C. %3D -200 mm 80 mm C "Rigid" (1) (2) 250 mm

Q The mechanical system, shown in the figure, consists of two identical steel rods (A 60 mm?, E= 200 GPa, a 12 x 10/ °C) and a "rigid" beam AC. The beam is supported by a smooth pin at B. The nuts at A and Care initially tightened just enough to remove the slack, leaving the two rods stress-free. Determine the axial stresses induced in rods (1) and (2) if the temperature of both rods is decreased by 60 °C. %3D -200 mm 80 mm C "Rigid" (1) (2) 250 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

904. To avoid interference, a link in a certain machine is de- signed so that its cross-sectional area is reduced one-half at section A-E, as shown in Fig. P-904. Compute the maximum tensile stress developed across section A-B if (a) the cross section of the link is 160 mm square and (b) the cross section is a circle 160 mm in diameter. Ans. (a) 75.0 MPa; (b) 85.3 MPa 80 mm P = 240 kN 80 mm B Figure P-904.
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1350 µm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. A 240 mm B (1) O 1281 um/m O 1877 µm/m O 1141 µm/m O 1358 µm/m O 999 µm/m 360 mm (2) Rigid bar 900 mm C 140 mm, 1,500 mm
Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 100 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 140 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 2300 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L2 (1) Aluminum B (2) Copper Answer: in, AL = i
3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
3.2 The rigid bar of negligible weight is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises by 20∘C after a load W = 110 kN is applied.
The rigid bar of negligible weight is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises by 20∘C after a load W = 110 kN is applied. Use the following properties in the table.
Two steel rods are welded together (see figure);the seam is oriented at angle θ = 50°. The stresses onthe rotated element are σ x1 = 10 ksi, σy1 = -12 ksi,and τx1y1 = -5 ksi. Find the state of plane stress onthe element if it is rotated clockwise to align the x1axis with the longitudinal axis of the rods.
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 78 GPa. The steel rod has a diameter of 16 mm and an elastic modulus of E = 200 GPa. Assumea = 4.1 m, b= 1.2 m, and c= 1.2 m. What is the magnitude of load P that is necessary to displace point A 12 mm to the left? a (1) (3) A B (2) Answer: P = i kN
i need solution thanks
Q2. Two members of Aluminium AB and BC are connected as shown in the Figure Q2.Point A is a fixed end support, point B is a pin connection and point C is a pin support. The cross section of member AB is 120 x 120 mm and member BC is a rod of 120 mm diameter. A forced P is applied to the connection B. Given the young modulus, E = 70 kN/mm² for both members. (a) Prove that both members are slender (Member is slender when the slenderness ratio, λ >90) (b) Determine the maximum load, P that can be carried by the structure. (c) Determine the allowable load, P if the factor of safety is 3.0. 4m P KN B 2m 2m 1m
For the assembly shown in the figure below, Determine the state of stress at point A on the cross section of the pipe at section a-a. 20 mm P 170N d 30mm Section a-a 120mm b 220mm