The rigid beam is supported by a pin at B and wires AD and CE. (Figure 1) The load P on the beam causes the end A to be displaced 6.5 mm downward. The wires are unstretched when the beam is in horizontal position. Figure 3 m D 2 m 2 m- < 1 of 1 > C 1.5 m- E 2 m Determine the normal strain developed in wire CE. Express your answer in millimeters per millimeter to three significant figures. ECE = Submit Part B IVE| ΑΣΦ | 11 vec X Incorrect; Try Again; 5 attempts remaining AD = Previous Answers Request Answer Determine the normal strain developed in wire AD. Express your answer in millimeters per millimeter to three significant figures. vec Submit G| ΑΣΦ | ? Request Answer mm/mm mm/mm

The rigid beam is supported by a pin at B and wires AD and CE. (Figure 1) The load P on the beam causes the end A to be displaced 6.5 mm downward. The wires are unstretched when the beam is in horizontal position. Figure 3 m D 2 m 2 m- < 1 of 1 > C 1.5 m- E 2 m Determine the normal strain developed in wire CE. Express your answer in millimeters per millimeter to three significant figures. ECE = Submit Part B IVE| ΑΣΦ | 11 vec X Incorrect; Try Again; 5 attempts remaining AD = Previous Answers Request Answer Determine the normal strain developed in wire AD. Express your answer in millimeters per millimeter to three significant figures. vec Submit G| ΑΣΦ | ? Request Answer mm/mm mm/mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The sanding-drum mandrel shown in the figure is made for use with a hand drill. The mandrel is made from a rubber-like material that expands when the nut is tightened to secure the sanding sleeve placed over the outside surface. If the diameter D of the mandrel increases from 1.90 in. to 2.00 in. as the nut is tightened, determine (a) the average normal strain along a diameter of the mandrel. (b) the circumferential strain at the outside surface of the mandrel. Sanding sleeve Answers: (a) ED (b) &c= = i i Mandrel in./in. in./in.
The vertical steel rod has a constant diameter of 32 mm and a length of 400 mm. is hanged from a rigid fixing. A mass is gently placed onto a collar which is attached to the lower end of the rod. The strain energy stored in the steel is 0.400 x 10-³. If Esteet = 209 GPa, 1.1 Determine the gradually applied load and magnitude of the mass. 1.2 Calculate the maximum stress in the rod when gradually applied. 1.3 Determine the magnitude of the mass when the mass is suddenly applied. 1.4 Calculate the extension of the rod when suddenly applied.
The sanding-drum mandrel shown in the figure is made for use with a hand drill. The mandrel is made from a rubber-like material that expands when the nut is tightened to secure the sanding sleeve placed over the outside surface. If the diameter D of the mandrel increases from 1.95 in. to 2.05 in. as the nut is tightened, determine (a) the average normal strain along a diameter of the mandrel. (b) the circumferential strain at the outside surface of the mandrel. Sanding sleeve Mandrel Answers: (a) ED = in./in. (b) Ec = in./in. Save for Later Attempts: 0 of 1 used Submit Answer
The rigid bar ABC pivots about support B. After application of load P, end C of the rigid bar moves upward by 0.06 in. If the length of bar (1) is L₁ = 51 in, determine the average normal strain in bar (1). Assume that a = 135 in., b=32 in., and c = 0.06 in. 4₁ 1 a Rigid bar B b
Learning Goal: To determine the average normal strain and average shear strain in a known material based on a given load and geometry. A flat plate ABCD distorts into the dashed shape ABCD shown after a load is applied with a (AC) v = Y Part A- Average normal strain along AC Determine the average normal strain (AC) avg along AC after the load has been applied. Express the average normal strain in millimeters per millimeter to three significant figures. View Available Hint(s) [ΕΙ ΑΣΦ 212 Yay= D Part B - Average shear strain at A Submit It vec ^ d C Yzy = Determine the average shear strain Yay at A relative to the x and y axes. Express the average shear strain in radians to three significant figures. ► View Available Hint(s) 15. ΑΣΦ ? ↓↑ vec Part C Average shear strain at point C 163.0 mm, b= 49.0 mm, 9 - 11.0 mm. f-18.0 mm, and e = 14.0 mm 195| ΑΣΦ | 41 mm/mm vec wwwww. Determine the average shear strain Yay at point C relative to the x and y axes after deformation. Express the average…
The sanding-drum mandrel shown in the figure is made for use with a hand drill. The mandrel is made from a rubber-like material that expands when the nut is tightened to secure the sanding sleeve placed over the outside surface. If the diameter D of the mandrel increases from 1.95 in. to 2.05 in. as the nut is tightened, determine (a) the average normal strain along a diameter of the mandrel. (b) the circumferential strain at the outside surface of the mandrel. Sanding sleeve D - Mandrel Answers: (a) ED = i in./in. (b) Ec= in./in.
When an axial load is applied to the ends of the bar shown, where L₁ = 30 in. and L₂ = 80 in., the total elongation of the bar between joints A and C is 0.100 in. In segment (1), the normal strain is measured as 1700 µin./in. Determine the normal strain in segment (2) of the bar. A (1) L₁ 662 μin./in. O 784 μin./in. O 373 μin./in. O 719 μin./in. O 613 μin./in. B (2) L2
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression vy/3E where y = 2.3 lb/in.³ is the specific weight of the material, y = 0.8 in. is the distance from the free (i.e., bottom) end of the bar, L = 8 in. is the length of the bar, and E = 23000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar. (c) the maximum normal strain in the bar.
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression yy/3E where y = 3.0 lb/in.³ is the specific weight of the material, y = 6.3 in. is the distance from the free (i.e., bottom) end of the bar, L = 21 in. is the length of the bar, and E = 27000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar (c) the maximum normal strain in the bar. Answer: (a) d = i (b) avg (c) Emax i x10-6 in. με με
Consider the pre-deformation cross-section of a bar, a side view of which is shown in the figure below. The diameter of the bar is d 180 mm. A bending moment is applied that causes the neutral axis to become concave up. What is the normal strain h = 30 mm from the bottom of the bar if the radius of curvature is measured to be p Express your answer to three significant figures. ▶ View Available Hint(s) £= - ΠΙΑΣΦ vec ? Ax mm/mm 5.4 m?
(a) Determine the shear strain at corner A if the plate distorts as shown by the dashed line. (b) Determine the average normal strain that occurs along the diagonal AC and DB. 5 mm 2 mm 4 mm 2 mm IB 300 mm $2 mm D A 400 mm 3 mm
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression yy/3E where y = 2.1 lb/in.³ is the specific weight of the material, y = 2.0 in. is the distance from the free (i.e., bottom) end of the bar, L = 5 in. is the length of the bar, and E = 27000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar (c) the maximum normal strain in the bar. Answer: (a) 8 = i (b) avg (c) Emax = i x10 in. με με