The Orange County Water District (OCWD) requires that the flow velocity in a water pipe cannot exceed 7 ft/s. Given a discharge of 3200 GPM, which of the following pipes is the BEST option? O NPS 8, schedule 80 O NPS 6, schedule 60 O NPS 4, schedule 40 O NPS 10, schedule 100

The Orange County Water District (OCWD) requires that the flow velocity in a water pipe cannot exceed 7 ft/s. Given a discharge of 3200 GPM, which of the following pipes is the BEST option? O NPS 8, schedule 80 O NPS 6, schedule 60 O NPS 4, schedule 40 O NPS 10, schedule 100

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Concern has been expressed at the local waste water treatment plant regarding the overflows caused…

A: Discharge (Q) = 100 m3/secMaximum Head =22 mLength (L) = 2050 mfriction factor (f) = 0.011To…

Q: characteristics of the two pipe system configurations (series and parallel) in terms of discharge,…

A: Given: Pipes in series Pipes in parallel To find: Discharge and headloss relationship Notations:…

Q: 0: A 1200 m long storm sewer collects wastewater from a catchment area of 50 hectare, where 35% area…

Q: The Stormwater Control Measure (SCM) behind McMichael Science Center is 140ft long, 50ft wide, and…

A: Given data, Dimensions of sto control measure Length L = 140 feet Width W = 50 feet Depth H = 3 feet…

Q: A rectangular channel is 25 ft wide and has a flow of 500 cfs at a velocity of 5 ft./sec. (a)…

A: Given:- The width of the rectangular channel = 25 ft The rate of flow = 500 cfs The velocity of the…

Q: Water flows at the rate of 0.16 L/s through a 200 mm diameter pipe. If its viscosity is 1.15x10-7…

Q: A 1:50 scale model of a spillway is to be tested in the laboratory. The discharge in the prototype…

A: Given- Scale 1:50. discharge Q=1000 M3/s. It is needed to find the discharge in the model test.

Q: A spillway model constructed to a scale of 1 : 4 gives a discharge of 10 m³/sec. The discharge from…

A: Spillway model scale Lr=1 : 4Discharge of model Qm=10 m3/sTo Find-The value of the discharge from…

Q: Two reservoirs having a difference of 40 ft in water elevations are connected by a 1.5-mile- long…

Q: The difference in energy grade line between inlet and outlet is 20 cm when Ethyl Alcohol (specific…

A: Given Data: Specific gravity of Ethyl Alcohol is S=0.79. Density of Ethyl Alcohol is given by:…

Q: I NEED THIS ASAPPPP What is specific energy in open channel flow? Draw a typical graph of depth vs.…

A: Given data in question Open channel flowDischarge is constant To find out Define specific…

Q: Wastewater of 30ft°/s with a biochemical oxygen demand (BOD) of 55mg/I, and dissolved oxygen (DO) of…

Q: Two final clarifiers following an activated sludge aeration tank have diameters of 60 feet and…

A: Given:- Diameter of clarifier = 60 feet Sidewall depth = 11 feet Mean diameter of effluent channel =…

Q: Two identical 12-in. storm sewers flow full at a 2% slope into a junction box. A single large pipe…

Q: A Pump station with a wet well is to be designed to handle an average daily wastewater flow of…

A: Data:Qav = Average flow = 175000 L/d = 1750001000×24×60Qav = 0.12153 m3/minQp = Peak flow = 560000…

Q: A spillway carries a discharge of 20 m³/s with the outlet velocity of 13 m/s at a depth of 0.25 m.…

A: Given data, Q = 20 m^3/s V1 = 13 m/s y1 = 0.25 m

Q: a) Concern has been expressed at the local waste water treatment plant regarding the overflows…

A: Given;Discharge (Q) = 100 m3/secMaximum Head =22 mLength (L) = 2050 mfriction factor (f) = 0.011

Q: Do Q2: A municipal wastewater treatment plant discharges secondary condition occurs in the summer…

A: Wastewater characteristics: Q1=10000 m3/d=0.116 m3/sC1=30 mg/lDO1=1.5 mg/lT1=25°C Stream…

Q: Hope your help hydraulic CEE 340

Q: Calculate Peak Wet Weather Flow given the following information about a wastewater treatment plant:…

A: Peak dry weather flow is given gyPDWF=Peak factor×ADWFADWF=Average Dry weather flowso,

Q: A sewer of 0.3 m diameter carries a discharge of 0.18 m³/s at half depth. If the depth of flow is…

A: 1. Diameter of the sewer: 0.3 m2. Discharge: 0.18 m/s3. Depth of flow at half depth.4. The depth of…

Concept explainers

Components of Hydroelectric Power Plant

A hydro electric power plant derives the energy from the force of fast moving water to harness energy. The demand for energy needs has impacted the environment resulting in global warming. Extensive use of non-renewable energy sources like petrol and diesel is the primary reason for environmental pollution. A major shift from non-renewable energy sources to renewable energy sources is the only solution to encounter the rising issue of environmental damage.

Question

The Orange County Water District (OCWD) requires that the flow velocity in a water pipe cannot exceed 7 ft/s. Given a discharge of 3200 GPM, which of the following pipes is the BEST option?
O NPS 8, schedule 80
O NPS 6, schedule 60
O NPS 4, schedule 40
O NPS 10, schedule 100

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Introducing given data

VIEW

Step 2: Select best size

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the downstream depth in a horizontal rectangular channel in which the bottom rises 0.75 ft, if the steady flow discharge is 550 cfs, the channel width is 5 ft, and the upstream depth is 6 ft. Also draw the specific energy diagram for this problem.
What effect do such losses have on your initial analysis of full-flow discharge? What other loss elements should be considered in the analysis? What value is there in your initial discharge analysis?
8.67 A 1/25 scale model of a spillway is tested. The discharge in the model is 0.1 m³/s. To what prototype discharge does this correspond? If it takes 1 min for a particle to float from one point to another in the model, how long would it take a similar particle to traverse the corresponding path in the prototype?
A rectangular channel 4 m wide has a depth of 2.5 m at a flow rate (discharge) of 12 m^3/s. Draw a specific energy diagram for the current flow conditions and determine whether the flow is sub-critical or super-critical ?
There are two main types of water distribution system layouts. In the Answer system, the main line is connected back to itself and the smaller lines join the main line at two or more locations. In the Answer system, a main distribution pipe is used, and smaller lines are connected to the main line at only one point along the length of the main line. The Answer is preferred over the Answer because it has isolation valves and water flows in more than one direction, which can avoid having to shut off water to all customers in an area during repairs. series looped branched system looped system parallel branched
Specify a suitable size of new, clean Schedule 40 steel pipe that would carry 300 gal/min of water over a length of 1200 ft with no more than 10 ft of head loss. For the selected pipe, compute the actual expected head loss.
Find the discharge through a 6” round orifice discharging freely. The water surface elevation in the impoundment is 568’. The elevation at the center of the orifice is 500’. Use a discharge coefficient of 0.62.
A 560 mm-diametre storm water pipe is built with a grade of 0.24 percent. What is the maximum capacity of this stormwater pipe sewer (I/s)?
3. A 55.0 ML/d wastewater treatment plant discharges to a river system with a maximum spring flow of 149.5 m3/min and a minimum summer flow of 98.2 m3/min (upstream of the outfall from the plant). What total allowable BOD (mg/L) could be discharged by the plant if the BOD in the river after dilution must not exceed provincial standards, and there is already 1.1 mg/L of pollution in the river upstream?
A municipal wastewater treatment plant (WWTP) receives a flow of 5.0 MGD. The WWTP does not have an equalization basin and therefore can have a peak hour flow that is 2.5 times the average daily flow. The WWTP has two circular, upflow clarifiers operating in parallel. The clarifiers must be designed to meet the following conditions: 1,000 gpd/ft (maximum) Average overflow rate = Peak overflow rate = 2,500 gpd/ft° (maximum) Basin depth = 10 ft What is the diameter of each primary clarifier? Hint: calculate the diameter for each a. of the given conditions, and select your diameter based on your results.
A sewer of 0.3 m diameter carries a discharge of 0.18 m³/s at half depth. If the depth of flow is reduced to 1/4th of the diameter, the discharge carried by the sewer is m³/s. (Round off to two decimal places)
PROBLEM #3 ONLY!!! Problem 1: A storm drain system is shown in Figure P16.11. For the flow conditions indicated, determine the time of concentration from Point A to Point C using the Kirpich, Kerby, Bransby-Williams, and Federal Aviation Administration Methods. Problem 2: Using the Kirpich time of concentration you calculated in Problem 1 and assuming the watershed is located in Seattle, WA, determine the intensity for the 50-year storm. Problem 3: For the watershed in Problems 1 and 2, determine the peak flowrate(in ft3/s )for the 50-year storm event at Point Cusing the Rational Method.