Two identical 12-in. storm sewers flow full at a 2% slope into a junction box. A single large pipe of the same material and slope flows out of the box. Assuming the following pipe sizes ar commercially available, the minimum size of this downstream pipe (in.) designed to flow full most nearly:

Two identical 12-in. storm sewers flow full at a 2% slope into a junction box. A single large pipe of the same material and slope flows out of the box. Assuming the following pipe sizes ar commercially available, the minimum size of this downstream pipe (in.) designed to flow full most nearly:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Concern has been expressed at the local waste water treatment plant regarding the overflows caused…

A: Discharge (Q) = 100 m3/secMaximum Head =22 mLength (L) = 2050 mfriction factor (f) = 0.011To…

Q: characteristics of the two pipe system configurations (series and parallel) in terms of discharge,…

A: Given: Pipes in series Pipes in parallel To find: Discharge and headloss relationship Notations:…

Q: Design a bar screen using the following data. Peak daily flow is 42 ML/day. Coarse screen bar will…

A: Peak daily flow (Q)=42 ML/dayCoarse screen bar= 1.48 cm width , 5.90 cm clear spacingApproach…

Q: Calculate the flow rate and average velocity for a 10-inch deep flow in the 12-inch diameter…

A: Given data in question Diameter 12 inch n value 0.028 Slope 0.0085 To find out Flow rate Velocity

Q: A surge tank is being designed to retard the water hammer in a 3,450-ft long pipeline with a…

A: Length = 3450ft Diameter = 6.5ft Discharge = 460cfs Maximum elevation = 16.5ft Required : Diameter…

Q: Given the data below, design a section of sanitary sewer to carry these flows at a minimum velocity…

A: minimum velocity of 0.6 m/s, n=0.013 minimum cover above the sewer pipe is 1.5m

Q: Determine the total sanitary sewer loading for the three pipes in the subdivision shown below. Also…

A: solve below calculationExplanation:Step 1: Step 2:Step 3: Step 4:

Q: discuss the differences between a full pipe flow and a partially full pipe flow.

Q: A spillway model constructed to a scale of 1:4 gives a discharge of 10 m³/sec. The discharge from…

Q: A system is being designed to carry 500 gal/min of ethylene glycol at 77°F at a maximum velocity of…

A: To determine Diameter of the schedule 40 steel pipe Reynolds number for the pipe diameter…

Q: a) Concern has been expressed at the local waste water treatment plant regarding the overflows…

A: Given;Discharge (Q) = 100 m3/secMaximum Head =22 mLength (L) = 2050 mfriction factor (f) = 0.011

Q: Hope your help hydraulic CEE 340

Q: A sewer of 0.3 m diameter carries a discharge of 0.18 m³/s at half depth. If the depth of flow is…

A: 1. Diameter of the sewer: 0.3 m2. Discharge: 0.18 m/s3. Depth of flow at half depth.4. The depth of…

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

Two identical 12-in. storm sewers flow full at a 2% slope into a junction box. A single larger
pipe of the same material and slope flows out of the box. Assuming the following pipe sizes are
commercially available, the minimum size of this downstream pipe (in.) designed to flow full is
most nearly:
(A) 16
(B)
18
20
24

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Data Given- diagram of pipe

VIEW

Solution- option A calcuation

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A waste water pipe has a length of 120 meters and is required to have a capacity of 50 L/s. The ground elevations are: 255.344 m @ upper end and 254.729 m @ lower end of the pipe. The minimum cover is 3.0 meters, and the permissible velocity range is 0.6 to 3.0 m/s. a) Identify the possible pipe sizes based on the Mannings nomograph in the Reference Module b) Draw a sectional view of one of the 2500 pipe. Show covers, pipe slope and inverts. c) Determine the partial velocity of the 2500 pipe using the hydraulics elements table in the Reference Manual. Consider an actual discharge of 10 L/s.
There are two main types of water distribution system layouts. In the Answer system, the main line is connected back to itself and the smaller lines join the main line at two or more locations. In the Answer system, a main distribution pipe is used, and smaller lines are connected to the main line at only one point along the length of the main line. The Answer is preferred over the Answer because it has isolation valves and water flows in more than one direction, which can avoid having to shut off water to all customers in an area during repairs. series looped branched system looped system parallel branched
Note: Subject environmental engineering 2
As a field engineer you are tasked to estimate the 25-year peak discharge for concrete parking lot that is 310 feet wide by 600 feet long using Rational formula. The longest flow path is 310 feet of sheet flow across the lot on a slope of 0.005 and 600 feet of shallow concentrated flow along the parking lot's length in a paved channel on a slope of 0.015. Use SCS procedures to determine the time of concentration using a 2-year, 24-hr rainfall of 2.4 inches. Use Figure below for the rainfall intensity in the rational equation. Intensity (in/hr) 0 10 20 25-yr average frequency 10-yr average frequency 30 40 -5-yr average frequency 2-yr average frequency 50 60 70 80 90 100 110 120 Duration (min)
Stop posting Ai solution
Specify a suitable size of new, clean Schedule 40 steel pipe that would carry 300 gal/min of water over a length of 1200 ft with no more than 10 ft of head loss. For the selected pipe, compute the actual expected head loss.
What is the maximum population that can be served by an 8-in. sanitary sewer laid at minimum grade using a design flow of 400 gpcd (gallon per capita per day) and a flowing-full velocity of 2.0 ft/sec? (b) Compute the diameter of a storm drain to serve the same population based on population density = 30 persons per acre, coefficient of runoff = 0.40, 10-year rainfall frequency curve, a duration (time of concentration) = 20 min, and a velocity of flow = 5.0 ft/sec.
Subject water system design
A 560 mm-diametre storm water pipe is built with a grade of 0.24 percent. What is the maximum capacity of this stormwater pipe sewer (I/s)?
ENVIRONMENTAL ENGINEERING
Design a concrete sewer required to carry a maximum design discharge of 10 cfs on a slope of 0.003. The minimum expected discharge is 2.5 cfs. Check the velocity for self-cleansing. Assume that commercial pipes are available in steps increasing by 0.5 ft (i.e. davail = 1 ft, 1.5 ft, 2ft, 2.5 ft...etc.)
A sewer of 0.3 m diameter carries a discharge of 0.18 m³/s at half depth. If the depth of flow is reduced to 1/4th of the diameter, the discharge carried by the sewer is m³/s. (Round off to two decimal places)