The motion of a pointer over a scale is resisted by a viscous damping torque of magnitude 4 N-m at an angular velocity of 2 rad / s. The pointer, of negligible inertia, is mounted on the end of a relatively flexible shaft of stiffness 2 N-m / rad, and this shaft is driven through a 1 to 4 reduction gear box. Determine the overall transfer function of the system? Gear box Pointer 0, If the input shaft to the gear box is suddenly rotated through 1 completed revolution, determine the time taken by the pointer to reach a position within 1 percent of its final value ?

The motion of a pointer over a scale is resisted by a viscous damping torque of magnitude 4 N-m at an angular velocity of 2 rad / s. The pointer, of negligible inertia, is mounted on the end of a relatively flexible shaft of stiffness 2 N-m / rad, and this shaft is driven through a 1 to 4 reduction gear box. Determine the overall transfer function of the system? Gear box Pointer 0, If the input shaft to the gear box is suddenly rotated through 1 completed revolution, determine the time taken by the pointer to reach a position within 1 percent of its final value ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q.2 A 75-kW induction motor runs at 740 rpm in clock direction as shown in the figure. A 19 teeth helical pinion with 20 degrees normal pressure angle, 10 mm normal module and a helix angle of 23 degrees is keyed to the motor shaft. Find: a) The transverse pressure angle. b) The pitch diameter of the pinion c) The pitch line velocity. d) Tangential, radial, axial and normal forces on the pinion. 750 200 ZIM 2₁ 19
Let Module 5 (m = 5) for a given mutual spur gear pair; Strength, Wear Load, Static Load and Dynamic Show if the conditions for load control are met? For pinion gear:Gear material strength Steel 2k = 900 N / mmSpeed: 1400 rpmd1 = 90 mmZ1 = 18 teethVery precise workmanshipHardness: BHN (Brinell Hardness Number) 400Gripping angle: 20 (full depth involute).It will transfer 22 kW of power For large gear:Gear material strength Steel k = 900 N / mm2d2 = 360 mm Acceptance and Table values: Value depending on tooth width: K = 4 (best value will be taken) Peripheral speed: V = 6 m / s Deformation coefficient: C = 171 kN / m Lewis factor: y = 0.102 Stress fatigue coefficient: k = 2553 kN / m2 Gear wheel width: b = 62 mm
A power source which is rotating at a constant speed of 500 rpm produces a variable torque as shown in Figure Q3. The maximum speed fluctuation is limited to 15%. Determine the following:- (i) (ii) (iii) The mean torque, Tm, hence the power of the source, Pi. The mass moment of inertia of the flywheel, I. The radius of the flywheel to be fitted to the system, if the material density is 6,000 kg/m3 and the ratio of radius to thickness is 3. T (Nm) 180 120 40 t (sec) 1 2 - 20 Figure Q3
m-5
only want sub D
A 2:1 speed reduction drive (Fig Q4) between two parallel shafts at 1200 mm centre distance is being provided by a V-belt of mass 0.5 kg/m. The diameter of the driving pulley is 200 mm and the driving shaft rotates at 900 rev/min. The driven pulley is 400 mm diameter. The angle of the pulley grooves is 40°, and the coefficient of friction between belt and pulleys is 0.35. If the maximum beit tension is 400 N determine: (i) The linear belt speed and the centripetal tension due to that belt speed. (ii) The angle of lap on each pulley (iii) The maximum power that may be transmitted Ø200 1200 Ø400
The motion of a pointer over a scale is resisted by a viscous damping torque of magnitude 4 N-m at an angular velocity of 2 rad / s. The pointer, of negligible inertia, is mounted on the end of a relatively flexible shaft of stiffness 2 N-m / rad, and this shaft is driven through a 1 to 4 reduction gear box Determine the overall transfer function of the system If the input shaft to the gear box is suddenly rotated through 1 completed revolution, determine the time taken by the pointer to reach a position within 1 percent of its final value
Q5 Design Straight bevel gear mesh for shaft centerlines that intersect perpendicularly with the following data Priori design Function Load (kW) 11 Speed (rpm) 924 Temperature (0C) 270 Pinion Life, NL (Cycles) 19232 Reliability 98.5 % Overload factor Uniform shock prime-mover and moderate shock load to the driven machine Gear ratio (mG) Varies 3 Design factor (nd) Varies 1.75 Tooth system Crown, straight bevel gears Straddle mounting One members straddle-mounted Crowned teeth conditions Larger uncrowned teeth Pressure angle (pn) 20 0 Tooth count Use within the range of 20 to 32 Design decisions Module (mm) 4 mm Face width (mm) 36 to 44 Quality number (QV) 8 Pinion materials Core and case hardened, Carburized and case hardness, Grade 2 Gear materials Core and case hardened, Carburized and case hardness, Grade 1 Hardness HBP = 475; HBG = 525
A belt pulley is designed as a flywheel. it has a moment of inertia of 100kgm^2 and is supposed to be accelerated from a resting position to a rotational frequency of 600 min^-1 within 15 seconds. you have to calculate the acceleration torque without considering the friction of the bearing
A spur pinion rotating at 20 rad/sec and having 20 teeth transmits 20 kW to a gear wheel. The pressure angle is 20° and module is 20mm. The reaction exerted by the pinion at the centre of thc shaft is
Calculate the derivatives of the Lagrangian to determine the torque equations for the one-link robot arm.
A planetary gear train is illustrated in the figure below. The carrier (link 2) serves as the input to the train. The ring gear (gear 1) has a 4-in pitch diameter and serves as th output from the train. The planet gear (gear 4) has a 3-in pitch diameter. The sun gear (gear 3) is fixed, it has 16 teeth with a diametral pitch of 12. Determine the rotational velocity of the ring gear when the input shaft rotates at 1600 rpm clockwise. - Gear 1 (ring) - Gear 4 (planet) - Link 2 (carrier) Gear 3 (sun)