The mass of block B is 95kg while that of A is 59kg. A horizontal force P=468N is applied at block A. The cutting angle is 30.296 degrees. Neglect friction. Computations must observe D`Alembert's Principle. a) Determine the normal force of contact between block A and block B. Express answer in Newtons or KiloNewtons. b) Determine the acceleration of block A. Express answer in meters per seconds. c) Determine the acceleration of block B. Express answer in meters per seconds.

Q: Q2: A: Find the maximum value of (p) that can be applied to the beam shown. = 350 MPa (WD.L is…

A: We have to determine the value of p that we can apply to the beam shown. Given data  fc=  21.7 MPa…

Q: The 2.0-kg collar is at rest in position A when the constant force Pis applied as shown. Determine…

A: Given, Mass of the collar, say M = 2 kg Force applied on the collar, P = 33 N Vertical distance…

Q: Calculate the minimum force P required to keep the 0.294 KN rod AB from sliding. The contact surface…

A:

Q: The beam of negligible weight is supported horizontally by two springs. The beam is horizontal and…

A: Objective: To determine the angle of tilt of the loaded beam.   Given: Spring constant of spring at…

Q: F2 -300 N F=700 N 60 M. =1500 Nm 2 m 3m or the above diagram, given that F, = 450 N, 8 = 30 degrees…

A:

Q: Two cantilever beams are arranged as shown in the figure. They have rectangular cross sections…

A:

Q: velocity of the collar is 0.1 m/s. The spring attached to the collar has an undeflected length of 10…

A: Given:- The mass of the collar = 2 kg The velocity of the collar at position 1 = 0.1 m/s The…

Q: The 670-N force is applied to the 110-kg block, which is stationary before the force is applied.…

A:

Q: The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m.…

A:

Q: Using CONJUGATE BEAM METHOD, Consider 150 mm x 200 (b x h) mm section and E = 80 GPa. Enter the…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: The 719-N force is applied to the 109-kg block, which is stationary before the force is applied.…

A: Given:- The magnitude of the force applied (P) = 719 N The angle of the force applied = 21° The…

Q: 190 N 255 N 120 N 710 mm 710 mm 710 mm

A: The step wise solutions along with figures are given below.

Q: A block of wood having a volume of 0.034 m and weighing 300 N is suspended in water as shown, a…

A:

Q: 400 mm -1100 mm- 200 N a 960 mm 400 N

A:

Q: The cross-sectional area of each clamp forming a fixed-supported cage system from points C and D…

A:

Q: The 687-N force is applied to the 119-kg block, which is stationary before the force is applied.…

A:

Q: Problem 1. Determine the smallest force P needed to lift block B. The coefficient of static friction…

A: Coefficient of static friction We all know that frictional force resists motion and is defined as…

Q: The coefficient of static friction between the drum and brake bar is μs = 0.4. If the moment M = 35…

A: Given:-  Coefficient of static friction between the drum and brake bar (µs) = 0.4 Moment = 35 N. m…

Q: The 679-N force is applied to the 114-kg block, which is stationary before the force is applied.…

A:

Q: Determine the steady-state angle a if the constant force P = 16O N is applied to the cart of mass M…

A: Given P=160N M=27kg m=7kg Theta=18°

Q: A force system is shown consists of Couple C and four forces. If the resultant of this system is a…

A:

Q: Question Bank - Friction The 40-N spool is suspended from the hanger GA and rests against a vertical…

A: Solution Given Data Weight= 40 N Static friction μ=0.25

Q: The 500-kg large chandelier is suspended from the wall and ceiling using rods AB and BC, which have…

A:

Q: The 440-N force is applied to the 91-kg block, which is stationary before the force is applied.…

A:

Q: Q#4. A block of 150 N is placed on the surface having coefficient of friction 0.4 (shown in figure).…

A:

Q: The solid shaft (G=70 GPa) has a diameter of 40 mm. Calculate: a. The magnitude and direction of the…

A:

Q: 2. A 1.25-kg block was released from the rest position at A by a compressed spring (k = 100 N/m).…

A: Given: k=100 N/m μx=0.25 To find: 1) Velocity of blocks at points B and C. 2) Normal force at point…

Q: At the instant shown, the slider D has a velocity of 3 ft/s up the channel and its speed is…

A: Given : The slider D has a velocity - 3 ft/s Decreasing speed at a rate of 0.5 ft/s2 To Find :

Q: Question 5 T/2 В 1200 Nm A homogeneous steel shaft (G=83GPA) is loaded as shown in the above Figure.…

A:

Q: The 700-N force is applied to the 100-kg block, which is stationary before the force is applied.…

A:

Q: The block A and the wedge B weighs 100 kN and 40 kN, respectively. The coefficient of fritction for…

A: Calculation Of angle of friction θ:- μ=tanθ⇒0.268=tanθ⇒θ=tan-10.268⇒θ=15°…

Q: 6/47 A block of mass mo is placed between the vertical wall and the upper end A of the uniform…

A: The given data is shown below: μs=0.5 Mass of the block placed between a vertical wall and upper end…

Q: Schematic diagram of a one degree of freedom bridge that can be opened and closed as follows. shown.…

A: