3 to e**dx,n = 10 1

Q: Problem 3 The figure presents the portion of the pipe network through which a fluid with a specific…

A:

Q: Calculate the angle, & by using equati on of motion in y direction. 1 y = y, +v t –: 150 150 0…

A:

Q: A RECTANGULAR ALUMINUM BLOCK IS 40mm LONG IN THE Y DIRECTION, 20mm WIDE IN THE Z DIRECTION AND 25mm…

A:

Q: Derive f from the given equation

A: Given data- 1f=-2.0log10ε/D3.7+2.51Ref To Find- The expression for "f".

Q: PROBLEM NO. 3 A uniform bar AB is resting in a horizontal position on smooth inclines as shown…

A:

Q: (1) = (ii) 8-1 3s (ii)

A:

Q: A tube well of 30 cm diameter F uifer. The strainer length is 15 m. Calculate the yield fre 3 m. The…

A:

Q: hree samples of Soll were collected dauring soll exxploration for of a Highrise Building a) Choose…

A: Solution: Three samples of Soil were collected during soil exploration for the construction of a…

Q: Situation 1]A private parcel was surveyed prior to the construction of a proposed fabrication plant.…

A:

Q: 4. The average spacing between vehicles in a traffic is 50 m, then the density (in veh/km) of the…

A:

Q: Question 24- At a certain point in the floor of weir, the uplift pressure head due to seepage is 5.4…

A: Given- Pressure head h=5.4 m, Relative density G=2.8, It is needed to find the minimum thickness of…

Q: 3. x? = Axy + By: A and B are arbitrary constants %3D

A:

Q: 3 Find the value of x if-1 X 1 x 3 4-30 1 0.

A: Solving matrix

Q: Consider the stress element as shown in figure. Determine the total distortion energy stored in 1 m…

A: For given state of stress,Young’s modulus of elasticity as E= 2 × 105 MPaPoisson’s ratio  0.3.

Q: Two wooden members of (25 b) (60 b)-mm uniform rectangular cross section are joined by the simple…

A: Given:- The cross-section of the two wooden pieces = 25×b×60×b mm2 The load on the wooden piece (P)=…

Q: If u = xy + 2y³x. v = -0.5y² + 6x³2 and w = 5y²x - y³z + x, then for a steady and incompressible…

A: Given- Velocity components- u=xy+λy3x,v=-0.5y2+6x3z,w=5y2x-y3z+x, Flow is steady and incompressible,…

Q: Determine the x 0.78P y and y components of the force system and the magnitude of the resultant and…

A:

Q: Two uniformly distributed loads of w = 3500 lb/ftact on the simply supported beam shown in Figure A.…

A: Find maximum bending compressive and tensile stress for BC.

Q: 7.29d.-1· 928 d² = e.97 > I 828 d= - デ. 29 d +0.97 = 0

A: This is a result of simple algebraic transformation. By shifting the terms on the left side of…

Q: Determine the linear impulse of the block at t = 3 seconds. %3D

A:

Q: Q 1: Find the first and second order partial derivatives of f(x,y, z) = x³ + 3x²y + ysinz

A: Given data: fx, y, z=x3+3x2y+ysinz

Q: d) Derive an equation for structure factor, S,using Fourier analysis.

A: Structure factor describes how a material scatters incident radiation. It is required to derive…

Q: Write F in vector form. у, ft F = 1450 lb 6.5 33° A 22 x, ft |2, ft B Answers: (express to 2 decimal…

A:

Q: =if e=0.538, then n 0.349 0.439 0.984 O 0.654 O 0.198 O

A: To find out the porosity of the soil when void ratio is 0.538.

Q: S(x* + 3x² + 5x)dx + f **

A: answer = x55+x3+3x2+4x+2lnx+Cexplanation is given in below step

Q: 1. The simplified general solution of (1 – x)y' = y² is

A:

Q: 3 seczx dx tanzx

A:

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.