A parcel of land, with boundaries as described below is to be subdivided into two lots of equal areas. The dividing line is to pass through a point midway between corners A and E, and through a point along the boundary BC. Find the bearing of this dividing line.

Q: in bullet form list structural work of beam

A: Structural work of beam

Q: Strain and Stress

A:

Q: 120N 80N 300

A:

Q: Prepare the details estimate for the following 2 roomed building

A: In this question, we have to calculate the total estimate of works

Q: Determine degree of external indeterminacy

A: Given data : Number of external support reaction (R)=3+1+1=5

Q: w H1 0.5 L 0.5L Figure 3 Activ. 6.2 Span "L" in metre Height (H1) in metre Live Load on the slab…

A: Strain energy hypothesis proposes that disappointment will happen when the strain energy per unit…

Q: Explain the minimum diameter of bar used in column ?

A: There are different shapes of bars are used in the construction. it is used to enhance the bond…

Q: How are forces between the tape and strips similar to those of magnetism?

A: The forces between a strip of adhesive tape and a surface are primarily due to intermolecular forces…

Q: Q4: Prove that:

A:

Q: one help please can you help me to draw an isometric view of the bridge (truss)

A:

Q: Provide description in each part of the universal testing machine

A: A Universal testing machine (UTM) is utilized to test the mechanical properties (pressure, pressure,…

Q: The elastic centroidal distance from the bottom is.. * 98 mm 212 mm 200.40 mm 89.50 mm

A: GIVEN DATA DEPTH OF WEB, DW=300 mm WIDTH OF WEB, BW=12 mm DEPTH OF FLANGE, DF=240 mm WIDTH OF…

Q: Problem 1 Wind blows on the side of a fully enclosed agricultural building located on an open flat…

A: When wind engineering is used to analyse tall buildings, the major load is frequently found to be…

Q: Describe about Rotational slides.

A: Slides refer to landslides, the movement of land mass is called a landslide. The mass of soil gets…

Q: Use the unit load method to calculate the vertical displacements at the quarter and mid-span points…

A: The given figure is shown below:

Q: draw stair tread and riser = 270 & 187 mm stair slab and landing thickness = 150 mm

A:

Q: Define Vertical Stresses.

A: The total vertical stress acting at a point below the surface of the ground is due to the weight of…

Q: Design Criteria of Column.Explain it

A: The design criteria for the columns are as follows: 1. Ultimate load on the column. The ultimate…

Q: A composite beam is fabricated by bolting two 2.5- in.-wide by 11-in.-deep timber planks to the…

A: Es = 30800 ksi Et = 1660 ksi Determine a. Maximum bending stress in timber and steel if P = 3.5…

Q: Discuss Designing for Shear

A: Introduction : Shear stresses in design normally operate in planes perpendicular to a member's…

Q: draw a structural base in a picture

A: Structural layout shows the structural components of a building like beams & colums. This layout…

Q: 250mm 250mm Reinforcing Bars

A: Given:-size-250mm x 250mmload =400kNallowable stress=8MPa for concrete and 150MPa for…

Q: Define the concept buckling.

A: Buckling Although, only compressive strength is the failure criteria for any short column, and some…

Q: Appendix 1 shows a structural drawing of the first floor of a random building. The labels "C"…

A: Structural drawing for the first floor of the building C- Columns D1–4 is a 200 UB 29.8,3C–D is a…

Q: QUESTION 12 List 2 methods that can be used to protect timber structural systems from termites. For…

A: Following are the two methods that can be used to protect timber from termites in Australia :

Q: 5. Among the following 3 choices, circle those choices where shear lag is an important factor in…

A:

Q: Define spudding

A: For drilling a well in a gas and oil industry, this process is used at the beginning.

Q: What is Spudding?

A: Spudding is defined as a process in which the drilling process of a well in any gas and oil industry…

Q: Make whatever changes or addition are necessary in each case to form a correct and complete FB.D.

A: 1) Incorrect, weight mg will act downwards 2) Incorrect, there will be frictional force acting at…

Q: 10) In case of architectural restrictions, the designer must: A) Place the rebars periodically B)…

A: Warning  is being given before answering,  However I do my best.  I try to give good explanation…

Q: Method of joints. AB, BD, BC

A: To find force in member AB,BD,BC

Q: draw a structural base in a picture

A: Structural layout shows the structural components of a building like beams & colums. This layout…

Q: 3. Draw the connection of a 150 mm Ølally column with a 50 mm x 75 mm purlin on top of a 50 mm x 100…

A: Diameter of the column - 150 mm purlin size- 50size of wood rafter - 50diameter of reinforcing…

Q: What is  negative skin friction ?

A: Friction is the resistance to motion of one object moving relative to another. It is not a…

Q: All are incorrect, can you re-work?

A: The degree of the curve = Da = 5°0' The intersection angle = 20°30' The station of the PI = 63+25.53…

Q: What is secondary compression?

A: Secondary compression:- It is a continuation of the volume change that started during primary…

Q: Differentiate half sectioning & full sectioning

A: Full  Sectioning  Half Sectioning  1. It is the full section view. 1. It is the half section view.…

Q: Compute the net area A, of the shape shown. Report your answer in in to the nearest two decimal…

A: