The hydrostatic transmission shown in the figure, is used to move a pulley attached to the shaft of the hydraulic motor. The actual flow rate of the hydraulic pump is 10 gpm, and the actual flow rate of the hydraulic motor is 7.5 gpm. The relief pressure is 2500 psi and the pressure in the inlet port of the hydraulic motor is 1000 psi. Calculate the power loss across the relief valve.

The hydrostatic transmission shown in the figure, is used to move a pulley attached to the shaft of the hydraulic motor. The actual flow rate of the hydraulic pump is 10 gpm, and the actual flow rate of the hydraulic motor is 7.5 gpm. The relief pressure is 2500 psi and the pressure in the inlet port of the hydraulic motor is 1000 psi. Calculate the power loss across the relief valve.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The load carrying crane shown in the figurethe drum with its rope wound with one hydromotorare driven. Object A is slanted as the rope hugsIt moves up and down over the sled.The diameter of the drum on which the rope is wound is 300 mm.All hydraulic system until hydromotor30% of pressure losses in the components (efficiency 0.7)It will be taken. Thread of hydraulic gear pump in one round0.8 lt of oil dispensed from the cavitiesSince it isa. Calculate the flow of the pump (lt / min)b. Find the working pressure of the pump (bar)Load speed v = 0.6 m / sTensile force on the rope T = 10,000 NIt will be taken.
A hydro electric installation is to develop 12 200 Hp. The head is 8ft and the speed of rotation is 150rpm. The specific speed of the turbine is not to exceed 485. What is the minimum number of units required? Select the correct response:
A centrifugal pump is used to pump water between two reservoirs as shown in the bellow figure. The dimensions and minor loss coefficients are provided in the figure. The pump rotates at 1600 rpm, the water inters the impeller normal to the blades and exits at an angle of 45° from radial. The inlet radius is 5.5-in, at which the blade width is 7.09-in. The outlet radius is 8.66-in, at which the blade width is 6.7-in. The volume flow rate is 23-cfm. Assuming 100 percent efficiency, calculate the net head produced by this pump in cm of water column height, the required brake horsepower in W and calculate the pump capability to pump water to upper reservoir. Reservoir z3-2, = 22.0 ft (elevation difference) D = 1.20 in (pipe diameter) KL. entrance = 0.50 (pipe entrance) KL. valve I = 2.0 (valve 1) KL. valve 2 = 6.8 (valve 2) Reservoir Valve 2 KL elbow = 0.34 (each elbow-there are 3) KLe L = 124 ft (total pipe length) e =0.0011 in (pipe roughness) = 1.05 (pipe exit) exit Pump Valve 1
Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft^3/s. Hint: You need to use the Tioga table and K value for minor losses. Z₂ = 107 ft Reservoir B 90° regular screwed elbow Pump Z₁ = 53 ft Reservoir A A) H=51+25.98(Q^2) B) H=54+24.98(Q^2) ⒸH=54+25.98(Q^2) ⠀
On the head side of a hydraulic cylinder, the rod is 1/2 inch in diameter and the piston is 2 inches in diameter. Calculate the force applied while retracting the rod and the speed at which it moves if the operating pressure is 150 psi and the flow rate is 6.5 gpm. Answer is incomplete without units.
A centrifugal pump develops a head of 16.8 m at 1500 rpm. Rated capacity is 0.015 m3/s. Determine the size of the impeller in mm if Øe=0.45.
As shown in the figure, the water flows from the ground floor of a three-storey house to the second floor through pipes of 20 mm diameter (average roughness of the pipe material = 0.0015 mm) at a volumetric flow rate of 0.75 L / s. Water is discharged from the system to atmospheric pressure through a tap with a 12 mm diameter outlet. There are 4 winged elbows, one ball valve and one faucet throughout the installation. Calculate the effective pressure at point 1. (psu=998 kg/m3, usu=1.12x10-3 Pa s, g=9.81 m/s2)
I ll rate
Higher volumetric efficiency pumps have very lesser slip losses. Select one: True False
A hydraulic motor has 7.5-in³ volumetric displacement. If it has a pressure rating of 1200 psi and receives oil from a 25-gpm theoretical flow-rate pump, find the motor a. Speed b. Theoretical torque C. Theoretical horsepower
A hydraulic motor receives a flow rate of 20 gpm at a pressure of 1800 psi. If the motor speed is 800rpm, determine the actual torque delivered by the motor assuming it is 100% efficient. (Would you mind please showing your work so I can understand how it is solved for studying purposes, thanks!)
The smooth pipes used in the pumping system in the figure below have a diameter of 150 mm. and its total length is 80 m. In this system; There are four bends with a loss coefficient of 0.2. Lost coefficients; 0.5 for the inlet to the pipe, 0.7 for the valve and 1 for the entrance to the tank. z2-z1 = 15 m above If the flow rate of the water pumped to the tank is 50 L / s and the overall efficiency of the pump is 84%, the manometric discharge Find its height and strength. Take the viscosity of water as 0.001 kg / m.s.