The four gears shown are attached to a steelshaft that is rotating at 2 Hz. Gear B supplies70 kW of power to the shaft. Of that power, 20kWare used by gear A, 20 kW by gear C and 30kWby gear D.G=83 GPa for steel-20KWJOKN -20kw -30kW2m1.5m1.5mB(a) If a uniform shaft diameter of 125 mmB speci fied, detenmine the angle of rotationof A relative to D.O f segment Co is to be replaced lay a hollawShaft with an inside diameter of 80 mm,what is the outside diameter if the stressis not to excced 70 MPa.

Answered: Image /qna-images/answer/2fb4485b-fdf9-498e-a397-1c5de7e62f41.jpg

The four gears shown are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20kW are used by gear A, 20 kW by gear C and 30kW by gear D. G=83 GPa for steel

The four gears shown are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20kW are used by gear A, 20 kW by gear C and 30kW by gear D. G=83 GPa for steel

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and is supported in rolling bearings at A and B. The applied forces are F₁ = 1600 lbf and F2 = 640 lbf. A steady torque of 1600 lbf-in is being transmitted through the shaft between the points of application of the forces. 1 / in ] A in [lin -10 in- F₁ in F₂ -10 in- All fillets in R. 12in] 3 in The value of the notch sensitivity is The value of the fatigue stress concentration factor is in NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. What is the value of the theoretical stress concentration factor for torsion, the notch sensitivity, and the fatigue stress concentration factor? (You must provide an answer before moving to the next part.) The value of the theoretical stress concentration factor for torsion is
The shaft shown in the figure below and rotating at a speed of 1 radian / sec transmits 9 kW of power from the gear at the B point to the pulley at the D point. Manufactured from cold drawn AISI 1040 steel, the shaft is machined to the given dimensions and bedded from A and C points. The highest working temperature of the spindle is 50 ° C. At point D; Since (d2 / d3 = 1.1) and (r /d = 0.1), determine the diameter d3 of the shaft using Goodman's theory. (kb = kc = kf = 1, q = 0.8 and qs = 0.9) 200 mm 140 mm 60 mm F1= 5F Fa Kasnak 160 Ry F2 = F Dig!! Ray Ray
A solid 1.9 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. The torque delivered by the shaft is 3500 lb-in. What horsepower must be delivered to the shaft to maintain a shaft speed of 520 rpm? What is the maximum shear stress developed in the shaft? Part 1 Convert the given shaft speed to units of rad/s. Answer: W= i rad/s
The motor in the figure applies a torsion (torque) of 50 Nm to the shaft AB. This torque is transferred to the CD shaft with the help of gears at points E and F. Bearings at B, C and D points provide free rotation to the shafts. Calculate the torque T' on the CD Shaft? 50 mm 30 mm B 35 mm T 125 mm
I need the answer quickly
Problem 2: Consider the two gears mounted on the shaft, as shown. Distances are L1 = 100 mm, L2 = 250 mm, and L3 = 175 mm. Diameter of shaft AB is 15 mm, diameter of shaft BC is 20 mm, and diameter of shaft CD is 17.5 mm. Young's modulus for each portion is 200 GPa. Determine the displacement of point D with reference to point A. Also, determine the displacement of point A relative to C. b. Determine the axial strain at any point in shaft segments AB, BC and CD, respectively. If Poisson's ratio for the material of the shafts is v = 0.2, determine the lateral strain in each of the shaft segments. Based on your answers to part (a), do the gears move towards each other, or do they separate from each other? Note that in real gearboxes, movement of gears towards or away from each other is prevented by using thrust bearings. 10 kN 4 kN 5 kN 7 kN 4 kN NY 0I 17.
A solid shaft 5 meters long is stressed to 55 MPa when twisted through 4 degrees. If G = 83 GPa. compute the shaft diameter in mm. What power in kW can be transmitted at 1200 rpm? O 59160.27 O 1155.74 O 44133.56 O 1160.60
Please answer in proper units
A compound shaft drives three gears, as shown. Segments (1) and (2) of the compound shaft are hollow bronze [G= 6,500 ksi] tubes, which have an outside diameter of 2.15 in. and a wall thickness of 0.2100 in. Segments (3) and (4) are solid 1.00-in.-diameter steel [G= 11,500 ksi] shafts. The shaft lengths are L₁ = 78 in., L₂ = 12 in., L3 = 20 in., and L4 = 26 in. The torques applied to the shafts have magnitudes of TB = 990 lb-ft, Tp = 450 lb-ft, and TE = 160 lb-ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. Using the sign convention presented in Section 6.6., calculate: (a) the magnitude of the maximum shear stress in the compound shaft. (b) the rotation angle of flange C with respect to flange A. (c) the rotation angle of gear E with respect to flange A. TB TD (1) TE (3) Answer: (a) Tmax (b) DC/A = (C) ΦΕΙΑ = LI (2) B psi rad rad C L3 D (4) LA E -X