A motor supplies 173 hp at 650 rpm to flange A of the shaft. Gear B transfers 75 hp of power to operating machinery in the factory, and the remaining power in the shaft is transferred by gear D. Shafts (1) and (2) are solid aluminum [G = 4400 ksi] shafts that have the same diameter and an allowable shear stress of T = 5.8 ksi. Shaft (3) is a solid steel [G=9100 ksi] shaft with an allowable shear stress of T = 10.2 ksi. Assume that L₁=2.3 ft, L₂=1.2 ft, L3=2.9 ft. Determine: (a) the minimum permissible diameter d₁=d₂ for aluminum shafts (1) and (2). (b) the minimum permissible diameter d3 for steel shaft (3). (c) the rotation angle DIA of gear D with respect to flange A if the shafts have the minimum permissible diameters as determined in (a) and (b).

A motor supplies 173 hp at 650 rpm to flange A of the shaft. Gear B transfers 75 hp of power to operating machinery in the factory, and the remaining power in the shaft is transferred by gear D. Shafts (1) and (2) are solid aluminum [G = 4400 ksi] shafts that have the same diameter and an allowable shear stress of T = 5.8 ksi. Shaft (3) is a solid steel [G=9100 ksi] shaft with an allowable shear stress of T = 10.2 ksi. Assume that L₁=2.3 ft, L₂=1.2 ft, L3=2.9 ft. Determine: (a) the minimum permissible diameter d₁=d₂ for aluminum shafts (1) and (2). (b) the minimum permissible diameter d3 for steel shaft (3). (c) the rotation angle DIA of gear D with respect to flange A if the shafts have the minimum permissible diameters as determined in (a) and (b).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: (Please input the FBD together with the answer) A flanged bolt coupling consists of nine-in diameter…

A: The torque capacity of the flange coupling is 5522.33 lb•ft.

Q: The steel shaft with two different diameters rotates at 4.5 Hz. The power supplied to gear C is 51.7…

Q: A flange bolt coupling has 10 steel coupling 1 inch diameter bolts evenly tighten around a 16.34 in.…

Q: A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid…

A: The allowable shear stress for brass shaft, The allowable shear stress for aluminum shaft, The value…

Q: A compound shaft drives three gears. Segments (1) and (2) of the compound shaft are hollow aluminum…

Q: The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and…

Q: A power source at C actuates valves at A and B through a long round steel control rod. A torque of…

Q: A compound shaft drives several pulleys, as shown. Segments (1) and (2) of the compound shaft are…

Q: The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and…

Q: A compound steel [G = 80 GPa] shaft consists of a solid 86-mm-diameter segment (1) and a solid…

Q: Q) A two-segment shaft is used to transmit power at constant speed through the pulleys shown above…

A: Solution:

Q: A compound shaft drives three gears. Segments (1) and (2) of the compound shaft are hollow aluminum…

Q: A 30 in. tubular shaft is in torsion under torque 33 lb-in.. Its cross section shown below with…

A: To find-: The shear stress at point B in psi. Given-: The torque of tubular shaft is T=33 lb.in. The…

Q: PROBLEM 2 As an Engineer, you have been tasked by your superiors to determine the shear stress and…

A: Find the angle of twist in AB and BC section of shaft. Find shear stress in AB and BC section of the…

Q: Q.1) Two torques are applied to the solid bronze (G= 6500 ksi) shafts of a gear system shown below.…

A: Consider the given figure. For the shaft AB, in equilibrium condition the torque acting on the gear…

Q: The small gear of an internal gear train shown in the figure is powered by a 500-kW motor at 30 Hz.…

A: Given data:

Q: A motor supplies 173 hp at 650 rpm to flange A of the shaft. Gear B transfers 75 hp of power to…

Q: 3. A steel shaft 60 in. long has applied to it a 10,000 in-lb torque by a pulley located at the…

Q: Torque =230 N-m

A: The torque for designing a rigid flange couple is given as, T=250 N-mT=250×103 N-mm The number of…

Q: A compound steel [G= 94 GPa] shaft consists of solid 28-mm-diameter segments (1) and (3) and tube…

A: Shear modulus of the compound steel (G): 94 GPa (or 94 x 10^9 Pa)Diameter of solid segments 1 and 3…

Q: A carbon steel shaft AB is fixed with two gears and is applied with 4 torque as shown in Figure 1.…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

A motor supplies 173 hp at 650 rpm to flange A of the shaft. Gear B transfers 75 hp of power to operating machinery in the factory, and
the remaining power in the shaft is transferred by gear D. Shafts (1) and (2) are solid aluminum [G = 4400 ksi] shafts that have the same
diameter and an allowable shear stress of T = 5.8 ksi. Shaft (3) is a solid steel [G=9100 ksi] shaft with an allowable shear stress of
T = 10.2 ksi. Assume that L₁=2.3 ft, L₂=1.2 ft, L3-2.9 ft. Determine:
(a) the minimum permissible diameter d₁=d₂ for aluminum shafts (1) and (2).
(b) the minimum permissible diameter d3 for steel shaft (3).
(c) the rotation angle D/A of gear D with respect to flange A if the shafts have the minimum permissible diameters as determined in (a)
and (b).
Answers:
(a) d₁=d₂ = i
(b) d3= i
(c) & DIA
=
i
(1)
L₁
TB.
B
(2)
L2
in.
in.
o'
(3)
L3
Tp
Mommu
D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given values in question

VIEW

Step 2: torque and diameter calculation

VIEW

Step 3: diameter calculation

VIEW

Step 4: rotation angle calculation

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A solid shaft with diameter 3 in. is to transmit 129 hp. If the shaft shownis rotating at 300 rev/min, calculate the max shear stress developed in the shaft: ____ ksi. Pay attention to units, and calculate your answer to 1 decimal place.
Like will be given :)
Homework help
The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power at 15 Hz to system at A. The yield shear stress is 140 MPa for shaft (1) and 220 MPa for the shaft (2), and over all factor of safety is 2. a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa, calculate the relative angle of twist D with respect to C. 30 teeth B (1) 48 teeth Tp 0.8 m
Parvinbhai
The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and is supported in rolling bearings at A and B. The applied forces are F₁ = 1600 lbf and F2 = 640 lbf. A steady torque of 1600 lbf-in is being transmitted through the shaft between the points of application of the forces. 1 / in ] A in [lin -10 in- F₁ in F₂ -10 in- All fillets in R. 12in] 3 in The value of the notch sensitivity is The value of the fatigue stress concentration factor is in NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. What is the value of the theoretical stress concentration factor for torsion, the notch sensitivity, and the fatigue stress concentration factor? (You must provide an answer before moving to the next part.) The value of the theoretical stress concentration factor for torsion is
A shaft drives a gear set that is transmitting 8 hp at 2250 rpm. The diameter of the shaft is 1.75 in. Determine the torsional shear stress developed in the shaft.