The following data were recorded when a centrifugal pump worked at its maximum efficiency: Q = 40 /ps ; Manometric head developed = 25 m; Input shaft horse power = 11.9 W. What is the non- dimensional specific speed of the pump it it was running at 1500 rpm? (May adopt the following (all in S.I. units): g=1-77, g¹/² = 3-132, g/=5.544, √√2=1.414,5 = 2.236 and 10 = 3.162)

The following data were recorded when a centrifugal pump worked at its maximum efficiency: Q = 40 /ps ; Manometric head developed = 25 m; Input shaft horse power = 11.9 W. What is the non- dimensional specific speed of the pump it it was running at 1500 rpm? (May adopt the following (all in S.I. units): g=1-77, g¹/² = 3-132, g/=5.544, √√2=1.414,5 = 2.236 and 10 = 3.162)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q_2,
he to another question will save this response. Question 10 Refer to the the flow shown in the figure. The velocity before the contraction is 1.68 m/s. Given: h = 0.31 m D1 = 0.108 m D2 = 0.069 m H Th h Da Free jet flow Determine the height of fluid in the manometer, H, in meters. Express your answer in 2 decimal places..
Imagine the water level in the tank described rises at a rate of 4 mm/s. Knowing the diameter of the tank is 240 mm, what is the average velocity of the water leaving the tank?
Kindly help me with this question. Thank you
ı need solution
Problem 13.27 The air in the reservoir has an absolute pressure of 350 kPa and a temperature of 30°C. The throat has a diameter of 50 mm. (Figure 1) Figure 50 mm 1 of 1 Part A Determine the greatest possible mass flow through the nozzle. Express your answer using three significant figures. m = Submit Provide Feedback AΣo↓ vec Request Answer ? kg/s
The setup shown in the figure is being used to measure the energy loss across a valve. The velocity of flow of the oil is 1.2 m/s. Calculate the value of K if the energy loss is expressed as K (v 2 / 2g). 1.0 m Oil (sg = 0.90) Flow 380 mm Mercury (sg = 13.54)
PLEASE I NEED HELP IN ANSWERING THIS ASAP. SUBJECT: HYDRAULICS NOTE: COMPLETE SOLUTION WITH PROPER FIGURES.
In the figure shown pipes are in parallel connection with properties given. If the flow into the system is 850lps with total head loss of 10 J/N. For the value of f=0.020 for all pipes, find the diameter of pipe 4. Pipe No. Length - m Diameter - em 1 1000 90 500 50 3 600 40 4 800 5 700 75
Use the following given values to solve problems, unless otherwise stated. Ywater = 9790 N/m³ = 62.4 lbf/ft°; g = 9.81 m/s? = 32.2 ft/s²; 1 hp = 550 lbf-ft/s = 746 Watts Problem-1 Water is pumped from the large tank through a uniform diameter pipe (d = 3 in.) and exits as a free jet (refer figure-a). The plot of the flowrate (Q) versus pump-head (hp) is a straight-line graph that passes through points (3, 16) as shown in figure-b. If the pipe friction head loss is, hf = 7V:/2g, where V is the average fluid velocity in the pipe, find a) the equation that relates hp and Q; b) flowrate and c) If the pump is 75% efficient, what horsepower is needed to drive it? Assume steady, incompressible flow. Ignore kinetic energy correction factor (a). 12 ft Pump %3D (a) 16 3. Q, ft°ls (b) dy
The water tank has a diameter of 750mm , a height of 1750mm to which the Initial height of water was 5 cm. If water was to be filled 90% of height and the water meter initial reading is 2000L, a. what is the final reading of the water in L b. Find the mass of water tank if its initial weight is 45 kg