Give me answer fast I will like your solution 4. (5 pts) From the figure below, pick the best impeller size for a pump with a flowrate of 400 gpm.The pump head curve is shown on the figure.कि ल1001750 RPM9.590980798.5"7074%708"TOTALHEADINFEET607.5SHP50 - 7404010HPNPSHR30IN30HP2020 FEET10100.100200300400500600700800US GALLONS PER MINUTE(5 pts) What is the efficiency at this point (to the nearest half of a percent)?78.97.(5 pts) What is the (NPSH)req'd at this point (in feet)?79.5SHP

(5 pts) From the figure below, pick the best impeller size for a pump with a flowrate of 40U gpi The pump head curve is shown on the figure. 100 9.5 90 1750 RPM 9 80 8.5" 70 8 TOTAL 60 HEAD 7.5 74% 70 94 79.5%

(5 pts) From the figure below, pick the best impeller size for a pump with a flowrate of 40U gpi The pump head curve is shown on the figure. 100 9.5 90 1750 RPM 9 80 8.5" 70 8 TOTAL 60 HEAD 7.5 74% 70 94 79.5%

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A discharge of 600 liters/sec flows through a pipe having a diameter of 400 mm., length of 40 m. long. Compute the head loss of the pipeline using Mannings Equation with n = 0.013. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m Decimal Places required in the final answer: 3
%07 3º,l|Asiacell نقطتان )2( * :Q6 The cylinder shown in the figure extends 8 ft into the paper. If the cylinder has the radius of 4 ft, compute the vertical component of the hydrostatic force of the oil on the cylinder. 90 Oil (s.g. = 0.85 ) 4 ft 50°
Given in the table are points in a pipe with some notes: B Pressure (kPa) 100 140 140 110 120 130 Elevation (m) 11 13 11 13 12 10 Velocity (m/s) 1 1.5 1.5 0.5 2 0.5 Which point has the highest total head? OD O F O E O A O B FL
The pipe flow in the figure is driven by pressurized air in the tank. Assuming f = 0.014 and the flow rate is 17.36 liters/sec. Find 20m-1 50mm 10m Find the head loss pipe gage pressure needed to provide the cuid water a Towirste 2132786 liters bec P open jet 100m 40m 8.84 2673.06 178.5 856.25 2157.3 3.58 210.2 OOOO оооо 382.2 73.5
1%VY lI. lu. Home work 1.pdf -> Home work 1 Three pipes of 400 mm, 200 mm and 300 mm diameters have lengths of 400 m, 200 m, and 300 m respectively. They are connected in series to make a compound pipe. The ends of this compound pipe are connected with two tanks whose difference of water levels is 16 m. If co-efficient of friction for these pipes is same and equal to 0.005, determine the discharge through the compound pipe neglecting first the minor losses and then including them. II
QUESTION 6 1S A dam is having a curved surface as shown in the figure. The height of the water retained by the dam is 20 m; density of water is 1000 kg/m. Assuming g as 9.81lm/s-Determine the magnitude and the direction of the resultant water x² pressure acting on a curved face of a which is shaped according to the relation y%3D 4 -20-m Click Save and Submit to save and submit. Click Save AllAnswers to saue all answers.
Suppose that a = 3.24 m and b= 1.8 m. (Figure 1). Figure y=x¹/2 b 1 of 1 > X Part A Determine the moment of inertia for the shaded area about the axis. Express your answer to three significant figures and include the appropriate units. Submit 0 ■μÃ xª Xh Value a Provide Feedback A X-10 Units Previous Answers Request Answer W X X Incorrect; Try Again; 23 attempts remaining ? Next >
Can Please Help Me: Civil Engineering 60 minutes only the given time. Wish you could help me. I will give UPVOTE and GOOD FEEDBACK. //Question A 2-foot diameter pipe carries stormwater discharge from a site. The concrete pipe was designed with a slope of 0.8 foot per 90 feet. At the time of measurement, the pipe has 0.8 feet of discharge flowing in it. What is the pipe discharge? (Express your answer in liter per second). Ans.205.1 lps //Question
Example 6.32. Water at the rate of 30 litres/sec. is flowing through a 0.2 m. I.D. pipe. A venturimeter of throat diameter 0.1 m is fitted in the pipeline. A differential manometer in the pipeline has an indicator liquid M and the manometer reading is 1.16 m. What is the relative density of the manometer liquid M? Venturi co-efficient = 0.96; Density of water = 998 kg/m'.
The pump in the figure draws water from a reservoir. At point A on the suction pipe an open manometer shows a vacuum of 290 mm of mercury, while a pressure gage at B reads 16 m of water. The total head loss of the pipes is 0.27 m. When the measured flow is 40 liters/sec, the input horsepower to the pump is found to be 16.4 hp. Compute the efficiency of the pump. Dia. of pipe is 150 mm for both suction and discharge pipes. 150 mnt d 4m /50mm+
7. Find the equivalent length of pipe 1 to 2 with a diameter of 300mm and the velocity of line C. Use the figure below and neglect minor losses. U 1 Pipes A B 3C A Length 300 m 150 m 250 m B 00 Diameter 300 mm 200 mm 250 mm C 10 m D f 0.020 0.021 0.020
As shown in the figure below, a Venturi meter is installed on a 300-mm diameter pipe whose maximum flow is 125 liters per second and the pressure head is 6.5 m of water. Determine the minimum throat diameter that will give a negative head. Solve for the discharge that will pass through the meter when the double column differential mercury gauge connected to it will show a difference of 25 cm. |25сm P. 36.5 h A2 300mmф Al ANSWER: a. D = 118mm b. Q = 87 liters/sec