A discharge of 600 liters/sec flows through a pipe having a diameter of 400mm., length of 40 m. long. Compute the head loss of the pipeline usingMannings Equation with n = 0.013.Do not write the unit. You will only input the numerical answer in the spaceprovided.Unit of the Correct Answer: mDecimal Places required in the final answer: 3

Answered: Image /qna-images/answer/799d0f71-3809-4bf5-8c2e-a72a2943731e.jpg

Answered: A discharge of 600 liters/sec flows…

A discharge of 600 liters/sec flows through a pipe having a diameter of 400 mm., length of 40 m. long. Compute the head loss of the pipeline using Mannings Equation with n = 0.013.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given the following: Diameter of Pipe = 1m, Length of Pipe = 845m and Head loss = 1.01 m, Determine the discharge using Mannings Formula, n=0.013 (A) 0.83 cms B) 0.63 cms 0.73 cms 0.93 cms
Situation 2 Pipelines 1,2, and 3 are connected parallel to each other. The three pipes carry a combined discharge of 0.86 m³/s. Pipe Length Diameter Friction Factor 400 mm 1,800 mm 1,500 mm 2,000 mm 1 0.020 X A 2 в У 2 350 mm 0.018 300 mm 0.022 3 4. Determine the flow rate through pipeline 1 (Q1) in m3/s. 5. Determine the flow rate through pipeline 2 (Q2) in m3/s 6. Determine the flow rate through pipeline 3 (Q3) in m3/s
ANSWER ASAP. WILL UPVOTE
A pipe network consists of pipeline 1 from A to B then at B it is connected to pipelines 2 and 3, where it merges again at joint C to form a single pipeline 4 up to point D. Pipelines 1, 2 and 4 are in series connection whereas pipelines 2 and 3 are parallel to each other. If the rate of flow from A to B is 10 liters/sec and assuming f=0.02 for all pipes. Determine the flow in each pipe and the total head lost from A to D.
Problem 2 The figure below shows a new cast-iron pipeline that connects two reservoirs. The upstream reservoir is at an elevation of 1000 ft (assume this is 1000.00 ft). The flowrate in the system from the upstream reservoir to the downstream reservoir is 5 cfs. Assume the water temperature is 50 °F. The pipe length from the first reservoir to the globe valve is 300 ft, the pipe length from the globe valve to the enlargement is 700 ft. (a) Using the Darcy Weisbach equation for pipe friction head loss, find the elevation of the downstream reservoir. Account for minor losses. Also tabulate the total head at each of the following locations along the pipeline: A just after the sharp-edged pipe entrance, B before the globe valve, C after the globe valve, D before the enlargement, E after the enlargement, F before the pipe exit. Calculate all values with a lot of precision because cumulative round-off errors can add up, but report all head values to the nearest 0.01 ft. Submit a clearly…
7.15 The following data were taken for turbulent flow in a circu- lar pipe with a radius of 3.5 cm. Evaluate the kinetic energy cor- rection factor. The velocity at the pipe wall is zero. r (cm) V (m/s) r (cm) V (m/s) 0.0 32.5 2.8 22.03 0.5 32.44 2.9 21.24 1.0 32.27 3.0 20.49 1.5 31.22 3.1 19.6 2.0 28.21 3.2 18.69 2.25 26.51 3.25 18.16 2.5 24.38 3.3 17.54 2.6 23.7 3.35 17.02 2.7 22.88 3.4 16.14
find the discharges in each of the pipes for the following pipe network configuration Given data L = 200 m D = 4cm f = 0.05 15 cumec A E B D с 15 cumec
PROBLEM 2 The elevations of water surfaces in reservoirs A and B are 300 ft and 250 ft, respectively, and discharge Q1 = 50 ft/s. Determine the following: (a) head loss (ft) in pipe 1, hu, (b) the elevation (el D') of the imaginary water surface at the junction, (c) the head loss (ft) in pipe 2, hua, (d) the flow rate (ft/s) in pipe 2, Q2. (e) the flow rate (ft/s) in pipe 3, Qa. (f) the head loss (ft) in pipe 3, ha, (g) the elevation of the surface of reservoir C, EI C. pipe L (ft) | d (in) 1 5000 36 0.0157 1500 24 0.0162 3 4000 18 0.0177 D
A pipeline of uniformly varying cross-section carries oil of specific gravity 0.87. The diameter of the pipe is 200 mm at end A and 500 mm at end B. The end B is located at 4 m higher than A. What is the loss of head in the pipeline if the pressure reading at A is 9.81 N/cm2 and at B is 5.886 N/cm²? (Take discharge is 200 litres/s and g = 9.81 m/s²)
Question 1 For the conditions given below, find the mass flowrate (lbm/sec). Density (p) is 62.4 lbm/ft³ 1. The pipe diameter (D) is 18 inches 2. The distance between MH1 and MH2 is (L) 300 feet 3. The invert (bottom of pipe) elevation at MH1 is (H1) 239 feet, and elevation at MH2 is (H2) 147 feet 4. Hazin-William coefficient (C) for good condition pipe is 120
Answer asap
A pipeline consists of three successive lengths of 50cm, 40cm, and 30cm pipes. With a continous discharge of 300 liters/s of oil sg=0.75. Compute the mean velocity in each pipe.