13. For the reservoir-pipe system shown in the figure given below, by considering the liquid as ideal (inviscid) find: a- The discharges in the pipes, b- Velocities and the pressures at points A, B, C,and D. c- Draw the gage and absolute energy and piezometer lines of the system.

13. For the reservoir-pipe system shown in the figure given below, by considering the liquid as ideal (inviscid) find: a- The discharges in the pipes, b- Velocities and the pressures at points A, B, C,and D. c- Draw the gage and absolute energy and piezometer lines of the system.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the open tank, the piezometers attached on the side, containing two different immiscible liquids, as shown in the figure, find the elevation of the liquid surface in piezometer A.
The pump whose characteristics are: H, = 80 – 600V²2 %3D n = -1500V² + 700V Elevation = 230 m |(2) (1) Elevation = 200 m 1000 m pipe 40 cm in diameter Pump Figure Q3 is used to pump water (µ=0.001kg/ms) a distance of 1000 m between two reservoirs the elevations of which are shown in Figure Q3 and remain constant. The pipe is 40 cm diameter commercial steel (ɛ=0.046 mm). Ignoring minor losses and assuming fully turbulent flow. Determine d) The volumetric flow rate e) The efficiency at the operating point
P10.) Determine the flow in each pipe shown in the figure. Assume f = 0.02 for all pipes. Subject: fluid mechanic Lesson: *Conservation of Energy *Fluid Flow in Pipes
The pump in the figure draws water from a reservoir. At point A on the suction pipe an open manometer shows a vacuum of 290 mm of mercury, while a pressure gage at B reads 16 m of water. The total head loss of the pipes is 0.27 m. When the measured flow is 40 liters/sec, the input horsepower to the pump is found to be 16.4 hp. Compute the efficiency of the pump. Dia. of pipe is 150 mm for both suction and discharge pipes. 150 mnt d 4m /50mm+
Situation 2: The figure shown below shows a pump drawing water from a reservoir and discharging it into the air at point B. The pressure at point A in the suction pipe is a vacuum of 10 in mercury and the discharge is 3 ft³/s. Determine the total head at point A and B with respect to a datum at the base of the reservoir. 10-in-diameter suction pipe 8-in-diameter discharge pipe Pump 15 f 25 ft "T 40 ft
The Bernoulli Equation can be written in terms of heights called heads. Define Energy Line and Hydraulic Grade Line in terms of head; and draw the Energy Line (EL) and the Hydraulic Grade Line (HGL) for the free discharge from a reservoir through a horizontal pipe with a diffuser shown in Figure.
11. A 350 mm by 150 mm venturi meter is installed in a vertical pipeline carrying water as shown in the figure. The flow is upward through the meter. A differential manometer containing carbon tetra-chloride (sg=1.5) is attached to inlet and throat. The difference Z in gage level is 700 mm. Neglecting the head loss, compute the discharge of the venturi meter 350 mm 150 mm 300 mm 700 mm
SUPPLEMENTARY QUESTION The figure shows two reservoirs connected by a pipe. The discharge rate in the pipe is known to be equal to SN/100 (m3/s) (where SN is the sum of your student number). Calculate the height of the second reservoir (H2), and the pressure head, velocity head and elevation head at point 3 (mid-point of the pipe). Hi 300 m H datum A = SN/1000 %3D L = 100 x SN (m) %3D D = 0.3 m
I need hand written solution only
As shown in the figure below, a Venturi meter is installed on a 300-mm diameter pipe whose maximum flow is 125 liters per second and the pressure head is 6.5 m of water. Determine the minimum throat diameter that will give a negative head. Solve for the discharge that will pass through the meter when the double column differential mercury gauge connected to it will show a difference of 25 cm. |25сm P. 36.5 h A2 300mmф Al ANSWER: a. D = 118mm b. Q = 87 liters/sec
The SN= 17
PROBLEM: Determine he from A toD in the system shown in the figure if the discharge is 1.60 m/s. Assume f= 0.02. 450 mm ø s 600 m 900 mm,90Om 750 mmø, 450 m A C. 4 D GOO mm 720 m (3