VPThe figure (not drawn to scale) shows a metallic cylindricalcolumn submitted to a combined load: bending and torsion. Thecolumn contains an hemispherical groove of radius r, located at adistance L from the point of application of the loads.You are giventhe column diameter D = 68 mm,the groove radius r = 6 mm,the distance L= 200 mm,the bending load P=5 kN,and the torque T = 600 N.m.The material data areYoung's modulus E = 122 GPaShear Modulus G = 55 GPaPoisson's ratio v = 0.1and Yield strength oy = 380 MPa.a) Write a numbered list of the calculation steps required toobtain the factor of safety in yielding based on the maximumdistortion energy (Von Mises) criterion.Enter your answer in the box below

Answered: Image /qna-images/answer/1cab85f0-9904-4cdc-8aba-7ece8154ae87.jpg

The figure (not drawn to scale) shows a metallic cylindrical column submitted to a combined load: bending and torsion. The column contains an hemispherical groove of radius r, located at a distance L from the point of application of the loads.

The figure (not drawn to scale) shows a metallic cylindrical column submitted to a combined load: bending and torsion. The column contains an hemispherical groove of radius r, located at a distance L from the point of application of the loads.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 3 The boom AB supports a load of W = 720 lb. The boom is supported by a ball-and-socket joint at A and by two cables, BC and BD. Find the tension in each cable and the axial force in the boom, assuming that point C is 4 inches vertically above the position shown in the figure and the other dimensions are unchanged. Neglect the weight of the boom. -9 in.- 8 in. B 12 in. W = 720 lb %3D
In the figure, torsional moments act on a bar system of abruptly changing cross-section made of the same material. Accordingly, calculate the value of the factor α so that the support responses are of the same magnitude in absolute value. What must the torsional moment=Mb be for the D-end to be zero? Note: The shear modulus of the material is G = 80 GPa Mo= 10 kNm.
Vertical load is applied to point B of a 10 mm radius cylindrical bar as shown in the figure. Calculate the shear stress occurring in the point.
The figure below shows a section of a column subjected to load P, which is applied 50 mm from the midline of the section's web. The column is made from material, which has an allowable normal stress of 180 MPa (both in tension and compression). The area of the section is 10050 mm?; the principal moments of inertia Imar = 146.554x106 mm and Imin 20.076x10° mm*. !! Determine the maximum allowable load P. 15 mm 150 mm 15 mm 150 mm 50 mm 15 mm 100 mm 100 mm 1194.6 kN 363.6 kN 1809.0 kN O 516.4 kN O 189.5 kN
Determine the torsion from the following figure. The torsional moment varies in the form of a parabola from 0 to t0 and t (x) = ax + bx + c, GJ is the axial stiffness.please i need help !!!!
Given:a. the force in BD=25KNb. vertical reaction at point C=-10KNc. horizontal reaction at point C=15KNd. resultant of reaction at point C=18.0KNe. allowable tensile (normal) stress in member BD =83.33MPaf. the allowable shear stress in the pin at C =72.7MPaPlease help me solve for:1. What is the required cross-section area and minimum thickness t of member BD?2. What is the required SHEAR cross-section area at point C?3. What is the minimum diameter for the pin at C?(Solve for a value with the combination of mm and N)
Please show the formula used and free body diagram A rectangular steel block is 4 inches long in the x direction, 3 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in the z direction. If ν = 0.30 and E = 29 × 106 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
The cable carrying three 400-N loads has a sag at C of hC = 14 m. Calculate the following: 26.1 The magnitude of the tensile force in segment AB is Blank 1 N. 26.2 The magnitude of the tensile force in segment BC is Blank 2 N. 26.3 The magnitude of the tensile force in segment CD is Blank 3 N. 26.4 The magnitude of the tensile force in segment DE is Blank 4 N.
A steel torsion bar AB with diameter d = 34 mm, and ductile material of tensile yield strength Sy = 276 MPa is attached to a rigid arm at A, supported by a bearing at C, and fixed at B, as the picture shows. At the right end of the arm is mounted the wheel on which the vertical force P acts from the ground and which passes through the center of the wheel. If bearing C acts as a simple support and the effect of transverse shear due to P is negligible, determine the maximum force P (in kN) that can be applied to the wheel. Consider a factor of safety n = 2.5. Use the maximum energy of distortion failure criterion and do the analysis on bar AB (torsion bar) in the section where the bearing is.
4. A ball in a cylindrical inner race has a radius of 5mm. The radius from the center of the race to the bottom of the groove is 20mm. If a load of 1,500N is applied: A. Find the dimensions of the contact ellipse B. Find the maximum deformation *Esteel = 207MPA, Vsteel = 0.3
The simply supported beam is subjected to the loads as described in the figure and parameter table. Neglecting the thickness of the beam, calculate the horizontal and vertical support reactions at A and B. F A B C -4*- L3 parameter value units L1 L2 L3 ft 4 ft 6 ft theta 65 F 200 lb M 500 lb-ft For the answers, take to the right and up to be the positive directions. The support reaction at A in the z direction is NAz- lb The support reaction at A in the y direction is NAy- lb The support reaction at Bin the z direction is NB= lb The support reaction at Bin the y direction is NBy= lb