A solid cantilevered aluminum alloy rod, 10-mm in diameter, supports a Parol (Christmas Lantern). The hanging Parol subjects the rod to a bending moment of 10.2 Nm along the x-axis, as well as Torque (T) at its fixed end (Section B). If the yield strength oYield in tension of the aluminum alloy is 103.9 MPa at point n of Section B, what is the maximum torque the rod can carry under the maximum distortion-energy theory (MDET)? L aluminum rod Figure 1A Y B cross-section of the rod Figure 1B Image is from Parol clipart 2 Clipart Station

A solid cantilevered aluminum alloy rod, 10-mm in diameter, supports a Parol (Christmas Lantern). The hanging Parol subjects the rod to a bending moment of 10.2 Nm along the x-axis, as well as Torque (T) at its fixed end (Section B). If the yield strength oYield in tension of the aluminum alloy is 103.9 MPa at point n of Section B, what is the maximum torque the rod can carry under the maximum distortion-energy theory (MDET)? L aluminum rod Figure 1A Y B cross-section of the rod Figure 1B Image is from Parol clipart 2 Clipart Station

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For a concrete column that is part of a braced frame, if the column is square, tied, 18 inches per side, 16 feet long, classify the column as slender or non slender. Assume that at one end of the column a clockwise moment of 100 k-ft is present, and that at the other end of the column a counter-clockwise moment of 25 k-ft is present. You may assume that K=1.
A brittle material made of ASTM grade 30 cast iron has ultimate strength in tension of 31 kpsi and ultimate strength in compression of 109 kpsi and undergoes the following plane of stress state: o, = 20 kpsi and Tyy = 10 kpsi (CW). a) using the 3D Mohr's circle, find all three principal normal stresses. b) using the Brittle-Coulomb-Mohr theory and Modified-Mohr theory, find the factors of safety for the given plane of stress state.
A hollow aluminum tube used is a roof structure has an outside diameter d2=70mm and inside diameter d1= 50mm. The tube is 2.5m long and the aluminum has a shear modulus of G=28 GPa. a.) If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist in degrees when the max shear stress is 50MPa? b.) What diameter 'd' is required for a solid shaft to resist the same torque with the same maximum stress?
Two forces are applied to a flywheel 50 cm in diameter. Each force is 500 N. The shaft is fixed to the wall using three grade 5 steel bolts. The distance between the bolts and the axis of rotation is 10 cm. (a) What moment of resistance must develop the three bolts together Answer: 250 Nm (b) What is the resistance force F of each bolt? Answer: 833.3 N (c) What is the diameter of the bolts if their factor of safety is 10? Answer: 4.14mm
3. The bar shown below is composed of two pieces, AC and CD. The bar is attached to the wall at point A. The length L = 10 in. The cross sectional areas are: AAC = 4 in? and AcD = 2 in?. The Young's Moduli are: EAC =20 Msi and Ecd= 15 Msi Two forces are applied at points B and D: PB = 50 kips and PD = 20 kips. Determine: (a) the reaction force at A (specify –→ or +) and (b) the deflection of point D (specify → or +). (Hint for (b): Think about how many pieces you must subdivide the rod into.) Ans: RA = 30 kips (+), dp = 7.9167×10-3 in (E) A В C D Pp L 2L L
SOLVE STEP BY STEP IN DIGITAL FORMAT DONT USE CHATGPT For the following structures, calculate -Reactions -Deformation diagrams (individual and general) (6) 7 100k/b ↓ +3ft + loft 80klb T +3ft +
A steel ring at a room temperature has a radius of R, of 1.00 mm x 1.00 mm. One like to insert a bar of radius R, = 2.002 cm into the ring. The following data is known for steel: 2.00 cm and a cross section area • Young Modulus E = 2.00 × 1011 Pa. • Coefficient of length contraction a = 1.20 x 10-5 C-1 • Specific heat capacity c = 511 J.kg-1.C-1 • Mass density p= 8050 kg.m -3 (a) What is the amount of heat needed for heating the ring so that the rod can fitted into it. (b) Assume the rod is rigid, calculate the pressure on the surface of the rod as the steel cool down to the room temperature.
A torsional moment T = 5,382 Nm and a load P = 55,253 N are applied at the same time to a circular hollow shaft of unknown length L, as shown in Figure Q5. The load P is offset from the centre of the circular cross-section by a distance e = 6 mm. The shaft has an inner diameter d = 43 mm and an outer diameter D = 97 mm. Point A in Figure Q5 is on the outer surface of the shaft. Figure 5 Calculate the direct (or normal) stress in the x-direction σx at point A (the 'x-direction' is along the longitudinal axis of the shaft, along its length L). Use π = 3.14159 if needed. Calculate your answer in the unit: mega-Pascal (MPa). Report you answer to 3 decimal places.
Problem 15 The compound bar shown below is made of a light, strong material with E= 70,000 N/mm². Two forces are applied to the rigid plates connecting the bars. The yield strength is o, = 200 N/mm². The bar has a rectangular cross section with height H = 12.5 mm and thickness t = 1.0 mm. You may neglect the weight of the bars. (a) Calculate the x-direction internal force in segments AB and BC of the compound bar. Show all work. (b) Calculate the total length change of the compound bar. (c) The plane 1-2 represents a lap joint. Calculate the normal stress on the lap joint. L₂= 625 mm A L₁ = 775 mm H = 12.5 mm X 1800 N B 1 H = 12.5 mm =35° 2 F₂ = 1000 N Cross section H-12 H = 12.5 mm t = 1.0 mm
Question 6 A B 112 mm 1.2 m 0.9 m Figure 6 The structure supports force P=75 kN, as shown in Figure 6. The solid circular rod BD is made of A992 steel: a. Find the vertical and horizontal component acting on the pin of the pulley C. b. Find the compressive force in the rod BD. c. Find the effective length-factor for BD. d. Express the radius of gyration about any centroidal axis for a solid circular area as a function of the diameter of a circle. e. Find the critical effective slender ratio (KL/r), according to the AISC specifications. f. Determine the required minimum diameter of the A992 steel solid circular rod BD to the nearest mm as allowed by the AISC specifications. g. Determine the F.S. for buckling of the designed rod DB. -0.9 m P