A prismatic bar of length L with a solid circular cross section of diameterd is loaded by a uniformly distributed torque of intensity t per unitdistance what is the angle of twist between the ends of the bar?AdTorque intensity = tLB

Answered: s loaded by a uniformly distributed…

Engineering

Mechanical Engineering

s loaded by a uniformly distributed torque of intensity stance what is the angle of twist between the ends of the bar?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.8.8P: A solid circulai' aluminum bar AB is fixed at both ends and loaded by a uniformly distributed torque...

See similar textbooks

Related questions

Q: An ASE automotive grade bolt with three slash marks on its head, indicates a hardness of what grade…

Q: Write the compatibility equation. Give consideration as to how it supports constrain shaft when it…

A: The compatibility equation make restriction to obtain how a strain can vary in a body for an assumed…

Q: Why is it important that the applied torques must not cause yielding of thematerial?

A: Torque causes twist in the cross sections of the member on which it is applied. If the applied…

Q: RB&W¹1 recommends turn-of-nut from snug fit to preload as follows: 1/3 turn for bolt grips of 1-4…

A: Please check the answer in the explanation. I hope you'll find this helpful.…

Q: Figure below shows a shaft that is loaded as given, l at points B and D to allow the shaft to…

A: In the given problem, Reactions will be determined by treating the beam to be in equilibrium and…

Q: What is the axis yielding?

A: A yielding is phenomena of give up to something like external pressure. to yield something does not…

Q: What are the three most critical materials properties linked to the functional demands of materials…

A: Given:Options are given with properties:

Q: Explain Self-locking and over-hauling conditions for a power screw using sketch and its formula.…

A: Torque Requirement - lowering the load…

Q: Compute the thread pitch and friction angle for a screw,

A: to compute the thread pitch and friction angle for a screw,

Q: A new machine in the machine shop will use an 02-series 45 mm deep groove bearing and operate with…

A: The given problem didn't provide load factors so Assuming typical load factors:X1=X4=1 for light…

Q: What size UNF bolt made from SAE grade 5 steel is needed to carry a static tensile load of 3000lb…

Q: Two single-row 02-series angular contact ball bearings with inner ring rotation are to be selected…

A: safe bore diameter is 80mm and OD is 140 mmExplanation:Step 1: Radial load on the bearing Fr = 3.5…

Question

A prismatic bar of length L with a solid circular cross section of diameter
d is loaded by a uniformly distributed torque of intensity t per unit
distance what is the angle of twist between the ends of the bar?
A
d
Torque intensity = t
L
B

Expert Solution

Step 1

$Given data as per question L = Length of prismatic bar d = Diameter of bar t = Intensity of Uniformly distrubuted torque$

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the approximate theory for thin-walled bars with the angle of twist 2 calculated from the exact theory of torsion for circular bars, Express the ratio 12terms of the non-dimensional ratio ß = r/t. Calculate the ratio of angles of twist for ß = 5, 10, and 20. What conclusion about the accuracy of the approximate theory do you draw from these results?
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A propeller shaft of solid circular cross section and diameter d is spliced by a collar of the same material (see figure). The collar is securely bonded to both parts of the shaft. What should be the minimum outer diameter dyof the collar in order that the splice can transmit the same power as the solid shaft?
A solid circular bar A BCD with fixed supports at ends A and D is acted upon by two equal and oppositely directed torques T0, as shown in the figure. The torques arc applied at points B and C each of which is located at distance x from one end of the bar. (The distance x may vary from zero to L/2.) For what distance x will the angle of twist at points B and C be a maximum? What is the corresponding angle of twist 0max?
A magnesium-alloy wire of diameter d = 4mm and length L rotates inside a flexible tube in order to open or close a switch from a remote location (see figure). A torque Tis applied manually (either clockwise or counterclockwise) at end 5, thus twisting the wire inside the tube. At the other end A, the rotation of the wire operates a handle that opens or closes the switch. A torque T0 = 0.2 N · m is required to operate the switch. The torsional stiffness of the tube, combined with friction between the tube and the wire, induces a distributed torque of constant intensity t = 0.04N m/m (torque per unit distance) acting along the entire length of the wire. (a) If the allowable shear stress in the wire is T allow = 30 MPa, what is the longest permissible length Lmaxof the wire?
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
Repeat Problem 2.3-4, but now include the weight of the bar. Sec Table 1.1 in Appendix I for the weight density of steel.
Repeat Problem 2.3-18, but assume that the bar is made of copper alloy. Calculate the displacements SBand Scif P = 50 kips, L = 5 ft = 3/5 in., b1= 2.75 in., b2= 3 in., and E = 16,000 ksi.
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
A solid circular bar ABCD with fixed supports is acted upon by torques T0and 2T0at the locations shown in the figure. (a) Obtain a formula for the maximum angle of twist 0maxof the bar. (b) What is 0max if the applied torque T0at B is reversed in direction?