The desired daily output for an assembly line is 360 units. This assembly line will operate 540 minutes per day. The following tablcontains information on this product's task times and precedence relationships:SABCDEFGHTASKсTASK TIME(SECONDS)5020805020303010IMMEDIATEPREDECESSORABABLOE-CG-F c. Balance this line using the largest number of following tasks. Use the longest task time as a secondary criterion. (Leave no cellsblank - be certain to enter "0" wherever required.)Work Station|||IIIIVTaskIdle Time

Given- Assembly line operate per day = 540 minutesDaily output of assembly line = 360 units

Answered: The desired daily output for an…

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

Discuss the term traditional assembly line operations and how are these operations efficient?
The following tasks are to be performed on an assembly line: TASK SECONDS TASKS THAT MUST PRECEDE A 30 — B 16 A C 21 B D 15 B E 17 C F 14 D G 20 E, F H 9 G The workday is 8 hours long. The demand for completed product is 900 per day. Find the cycle time required to meet the desired output rate. Note: Round your answer to 1 decimal place.
snip
Master schedules are expressed in three different waysdepending on whether the process is continuous, a job shop,or repetitive. What are these three ways?
Can you assit me with this problem 3 by showing me the process step by step. I prefer it not be in the form of an excel sheet because it is hard to follow along. Thank you kindl
A manufacturing plant has the process displayed below. The drilling operation occurs separately from and simultaneously with the sawing and sanding operations. The product only needs to go through one of the three one of the three assembly operations (the assembly operations are ‘parallel’). Use diagram titled "q3" attached as an image a) What is the bottleneck operation? b) What is the throughput time for the overall system? c) If the firm operates 10 hours a day, 21 days a month, what is the monthly and yearly capacity of the manufacturing process? d) Supposed that a second drilling machine is added, and it takes the same time as the original drilling machine. What is the new bottleneck time of the system? e) What is the new throughput time if the second drilling machine is added? f) What is the new hourly capacity if the second drilling machine is added?
T. Smunt Manufacturing Corp. has the process displayed below. The drilling operation occurs separately from and simultaneously with the sawing and sanding operations. The product only needs to go through one of the three assembly operations (the assembly operations are “parallel”). See attached image with outline a. Which operation is the bottleneck? b. What is the throughput time (time from start to finish for one unit) of for the overall system? c. If the firm operates 8 hours per day, 22 days per month, what is the monthly capacity of the manufacturing process? d. Suppose that a second drilling machine is added, and it takes the same time as the original drilling machine. What are the new bottleneck operation and the bottleneck time? e. Suppose that a second drilling machine is added, and it takes the same time as the original drilling machine. What is the new throughput time? f. Suppose that a second drilling machine is added, and it takes the same time as the…
Some tasks and the order in which they must be performed according to their assembly requirements are shown in the following table. These are to be combined into workstations to create an assembly line. The assembly line operates 11.9 hours per day. The output requirement is 1,020 units per day. PRECEDING TIME PRECEDING ΤΙME TASK TASKS (SECONDS) TASK TASKS (SECONDS) A 32 G 13 В A 19 H D 12 A 15 I E 9 В 14 F, G н, I J, к 15 B 10 K 19 12 L 15 a. What is the workstation cycle time? Workstation cycle time seconds per unit b. Balance the line using the longest task time rule based on the 1,020-unit forecast, stating which tasks would be done in each workstation. (Leave no cells blank - be certain to enter "O" wherever required.) Work Station Task Idle Time II IV V VI
What is a heuristic? Name several that can be used in assembly-line balancing.
A shop works a 400-minute day. The manager of the shop wants an output of 200 units per day for the assembly line that has the elemental tasks shown in the table. Do the following:a. Construct the precedence diagram.b. Assign tasks according to the most following tasks rule. Break ties with the greatest positional weight rule.c. Assign tasks according to the greatest positional weight rule. Break ties with the most following tasks rule.d. Compute the balance delay for each rule. Which one yields the better set of assignments in this instance? TaskImmediatePredecessorTaskTimea — 0.5b a 1.4c a 1.2d a 0.7e b, c 0.5f d 1.0g e 0.4h g 0.3i f 0.5j e, i 0.8k h, j 0.9m k 0.3
Please answer all sub-parts question

Recommended textbooks for you

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Business in Action

Operations Management

ISBN:

9780135198100

Author:

BOVEE

Publisher:

PEARSON CO

Purchasing and Supply Chain Management

Operations Management

ISBN:

9781285869681

Author:

Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson

Publisher:

Cengage Learning

Production and Operations Analysis, Seventh Editi…

Operations Management

ISBN:

9781478623069

Author:

Steven Nahmias, Tava Lennon Olsen

Publisher:

Waveland Press, Inc.

SEE MORE TEXTBOOKS