The control arm is subjected to the loading shown. Determine to the nearest the ¼-in. required diameter of the steel pin at ‘C’ if the allowable shear stress for the steel is 8-ksi.

Q: The yoke-and-rod connection is subjected to a tensile force P. The end of the 40-mm diameter rod is…

A:

Q: Q2/ Segments AB and BC of the assembly below are made from 6061-T6 aluminum. If a couple forces P= 5…

A: ∑Mx=0Ta+Tc-3X5=0                           (1) COMPATABILITY,…

Q: A gear motor can develop 5 hp when it turns at 200 rpm. If the allowable shear stress for the shaft…

A:

Q: The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the magnitude of the…

A:

Q: Please solve this question in detail. You have to add the free body diagram.

A:

Q: Determine the shearing stress in the pin with diameter equal to 30 mm. Express the answer in MPa.…

A:

Q: Determine the maximum average shear stress developed in each -in diameter bolt for the system shown…

A: Given:- d=3/4 in To find:- Maximum shear stress

Q: Determine the stress area in mm2 of a 1.75 - 8UNC bolt.

A:

Q: (D) The pin used at B has an ultimate shear strength of 58 ksi. If a factor of safety of 2.5 is…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked.…

Q: of 3.0 mm is produced at the tom of the groove. Compute the maximum stress in the rod y axial…

A:

Q: A 120-mm diameter bolt is used in a clevis. Determine the shear stress on the bolt if a load of 350…

A: Given data,  d= 120 mm  F= 350 kN =350000 N

Q: The 3.4-m in length cylindrical shaft (made of unknown material) is subjected to the applied…

A:

Q: SIMPLE STRESSES B. 1. Rod AB carries 500 kg cylinder at B, and it is supported by a hinge at A.…

A:

Q: Steel wire AB and aluminum wire CA support the 400 kg mass as shown. Determine the required diameter…

A:

Q: The uniform 3-Mg bar is supported by a smooth wall at A and pin connected a B (double shear).…

A:

Q: The boom is supported by the winch cable that has allowable normal stress of sallow = 24 ksi. If it…

A: Free Body Diagram →…

Q: Q1- Prove that the shear stress of circular shaft under pure torsion is Tr Tmax Ip Ex

A:

Q: rotating at a constant speed. The angle of twist between A and D is limited to 1.50 degree. Use…

A:

Q: Determme the snallest allowable diameter of the solded shuft ABCD, knowng that the allowable shear…

A: Given data as per question Allowable shear stress = 60 Mpa The radius of disc B =80 mm…

Q: the pins at A and B if the allowable normal stress for member BC is Oallow = 35 ksi and the…

A: Handwritten.jpg

Q: Determine the maximum torque of the tube shown if the allowable shearing stress is 46 Mpa. Given: t…

A: Given data:allowable shear stress = 46 MPat = 2.73 mma= 33 mm

Q: The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by…

A: To find: The shear stress in the pin. Given: The diameter of the steel tube is d=4 in. The wall…

Q: 3) If the maximum torsional shear stress for the shown circular shaft is 4000 psi, the torsional…

A:

Q: 1- The cross section of the machine part is a square, 5 mm on a side. If the maximum stress at…

A: According to the given information, the side of the square is 5 mm and the stress is 150 Mpa. The…

Q: The following shaft is free at A and connected to a fixed support at C. The shaft has a solid…

A: For solution refer below images.

Q: Determine the shearing stress in the pin with diameter equal to 25 mm. Express the answer in MPa.…

A:

Q: Q2/ The assembly consists of two sections of cast-iron rod connected together using a reducing…

A: Given data :- for section AB L = 12 in , d = 0.75 in for section BC L = 15 in , d = 1 in shear…

Q: 3. Determine the largest shear force V that the member can sustain if the allowable shear stress is…

A:

Q: A spring was made by a steel wire of 25 mm diameter around a 175 mm diameter cylinder. determine the…

A:

Q: 5. The steel tube has an elliptical cross section of mean dimensions shown and a constant thickness…

A:

Q: The beam is constrocted from two boards fastened together with nails as shown If F spag eds pannbas…

A:

Q: Determine the normal stress at A and B if the blade of the coping saw has a tension of 40 Newtons.…

A: Tension P = 40 N Find the normal stresses at point A and B

Q: The shaft below is hollow from A to B and solid from B to C. Determine the maximum shear stress in…

A:

Q: If A and B are both made of wood and are 3 8 in. thick, determine to the nearest 14 in. the smallest…

A: Provided that both the elements A and B are 3/8 inch thick. The applied force of 800 lb will have…

Q: a force q of magnitude 3kips is applied to machine element ab. the uniform thickness of the element…

A: Given data Force (Q) = 3 Kips Thickness (t) = 0.8 in

Q: ● ● ● the rigid bar AB is on a smooth incline the 5/8 diameter pin at B is in double shear Determine…

A: Given:Force acting on th ebeam, F=2000 lbDiameter of the pin, d=58 in

Q: Determine the average shear stress in the tube if the dimension a = 200 mm

A:

Q: The solid shaft (loaded as shown) is made of material that has an allowable shear stress of 10 MPa.…

A: The solid shaft (loaded as shown) is made of material that has an allowable shear stress of 10 MPa =…

Q: Q1- Prove that the shear stress of circular shaft under pure torsion is Tr %3D Tmax Ip

A: Given Circular shaft To find ζmaax=TrIP

Q: Determine the maximum w that can be applied if the shear stress limit is 100 MPa. Then determine the…

A:

Q: An assembly is subjected to a torque (710 lb-in). If the allowable shear stress for the material is…

A: Given:Diameter of smaller section = d = 0.75 inDiameter of bigger section = D = 1.5 inTo find:The…

Q: A 22.2 mm diameter bolt having a diameter at the root of the threads of 18.6 mm is used to fasten…

A: Given data as per question diameter of bolt =22.2 mmRoot diameter of thread =18.6 mmLoad =34…

Q: N M MI 6 mm F₁ 10 kN. The pin at point M has a radius R. F.S.=2.5 a=250 mm & b=200 mm Angle between…

A: Shear stress is a force that tends to distort a material by causing it to slip along a plane or…