3. Gear B supplies 20 KW of power, while gears A, C and D withdraw 6 kW, 4 kW and 10 kW, respectively. If the shaft is made of steel with the allowable shear stress of 80 MPa, and the relative angle of twist between any two gears cannot exceed 0.065 rad, determine the required minimum diameter d of the shaft to the nearest millimeter. The shaft is rotating at 800 rpm. B 600 mm 600 mm D 600 mm

Q: The 54-mm diameter shaft is subjected to the torques as shown. Determine the angle of twist (in…

A:

Q: A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid…

A: According to the given dataWe need to findminimum required diameter for the segments 1 and 2

Q: The shaft is made of A-36 steel, has a diameter of 95 mm, and is fixed at B while A is loose and can…

A: Write the given data.

Q: The drive shaft of the motor is made of a material having an allowable shear stress of τallow= 72…

A:

Q: The shaft is made of A-36 steel and has a diameter of 70 mm. It is fixed at B and the support at A…

A:

Q: 1. The splined ends and gears attached to the A-36 steel shaft are subjected to the torques shown.…

A: Given data: d=40 mmShaft=A-36 steel Need to determine the angle of twist of end B with respect to…

Q: 300 N-m 500 N-m The solid 30-mm-diameter shaft is used to 200 N-m transmit the torques applied to…

A: It is required to determine maximum shear stress

Q: The 63-mm diameter shaft is subjected to the torques as shown. Determine the angle of twist (in…

A:

Q: The loads illustrated produce concentric axial force in the 20-mm-diameter shaft, which is made of…

A:

Q: The driveshaft of an automobile is being designed to transmit 172 hp at 2950 rpm. Determine the…

A:

Q: Determine the maximum shear stress in segment AB.

A: To find Maximum shear stress in segment AB

Q: the diameter of solld snaft (2) IS E. 72 teeth 30 teeth (1) (2)

A: Givenspeed of motor NA=808rpmZA=24ZB=72ZC=30ZD=60

Q: Q.1) Two torques are applied to the solid bronze (G= 6500 ksi) shafts of a gear system shown below.…

A: Consider the given figure. For the shaft AB, in equilibrium condition the torque acting on the gear…

Q: A motor supplies 173 hp at 650 rpm to flange A of the shaft. Gear B transfers 75 hp of power to…

A:

Q: 3. Gear B supplies 20 KW of power, while gears A, Cand D withdraw 6 kW, 4 kW and 10 kW,…

A: Answer: The required minimum diameter of the shaft is 24.5 mm.

Q: The design of a machine element calls for a 40-mm-outer-diameter shaft to transmit 41 kW.   NOTE:…

A: For shaft a, Given data is d= 40 mm  N= 720 rpm  P= 41 KW

Q: A motor supplies 173 hp at 650 rpm to flange A of the shaft. Gear B transfers 75 hp of power to…

A:

Q: a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa,…

A: for solution refer below images.

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.