5. The steel tube has an elliptical cross section of mean dimensions shown and a constant thickness of t = 5 mm. If the allowable shear stress is 56 MPa, and the tube is to resist a torque of 340 N.m, determine the necessary dimension b. 0.5b B 340 Nm

5. The steel tube has an elliptical cross section of mean dimensions shown and a constant thickness of t = 5 mm. If the allowable shear stress is 56 MPa, and the tube is to resist a torque of 340 N.m, determine the necessary dimension b. 0.5b B 340 Nm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A machinery uses a helical tension spring with wire diameter of 3 mm and coil outside diameter of 35 mm. The spring has 9 total coils. The design shear stress is 500 MPa and the modulus of rigidity is 82 GPa. Determine the force that causes the body of the spring to its shear stress in N. Consider ground ends.
Determine the maximum shearing stress in a bronze helical spring composed of 19 turns of 0.96-in.-diameter wire on a mean radius of 3.53 in. when the spring is supporting a load of 516 Ib. Use the equation for heavy spring and G = 6 x 10° psi. (Answer must be in Ib per square inch) Round your answer to 2 decimal places. Add your answer
The solid steel shaft has a diameter of 35 mm. Determine the absolute maximum shear stress in the shaft.
The solid rod with radius r=37 mm is subjected to the loading F;=120 kN, F2=38 kN, F3=29 kN. With dimensions a=210 mm and b=330 mm Determine the magnitude of the combined shear stress at point B, given the following: Section Properties: b A=4300.84 mm? |= 1471963 mm A J= 2943925 mm4 Qmax= 33769 mm? B. O 0.310 MPa O 0,007 MPa O 0,620 MPa O 6.615 MPa O 4.805 MPa O 40.147 MPa O 13.176 MPa
The handwheel shown consists of the shaft, flange, and handle. A force P = 1 kN is applied to the handle as shown. The dimensions a and b are 110 mm and 220 mm respectively. If the diameter of the shaft is 24 mm, determine the maximum normal and shearing stress in the shaft. FLANGE a SHAFT HANDLE
A1 m long and 35 mm diameter aluminum shaft is to be replaced by a steel hollow shaft of the same length and the same outside diameter. It is required to design the steel shaft to withstand double the shear stress that of aluminum shaft. Determine the inside diameter of the stee I shaft. Find the values of the shear stresses on each shaft if a torque of 3 kN.m is applied to both of d=20mm them.
4. The shaft shown transmits 1 kW of power at 1000 rpm. Determine the maximum stress in the shaft. Ø20 mm Ø16 mm 0.5 mm corner radius
Solve by hand and correctly solve otherwise skip it
4) The composite shaft consists of a solid brass segment (1) and a solid aluminum segment (2) that are connected at flange B and securely attached to rigid walls at A and C. Brass segment (1) has a diameter of 18 mm, a length of L₁ = 235 mm, and a shear modulus of 39 GPa. Aluminum segment (2) has a diameter of 24 mm, a length of L₂ = 165 mm, and a shear modulus of 28 GPa. If a concentrated torque of 270 Nm is applied to flange B, determine (a) the maximum shear stress magnitudes in segments (1) and (2). (b) the rotation angle of flange B relative to support A. N y A 235 mm (1) B 165 mm 270 N-m (2) C x
The solid bar ABCD consists of three segments subjected to three (3) torsores as shown below. If G = 11.6x10 ^ 6 pounds / inches. Determine: 1. Where the maximum shear stress is recorded and what is its magnitude. 2.The angle in radians that rotates point D.
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 72 mm and G = 30.49 GPa. For the steel segment BC, the diameter is 48 mm and G = 83.57 GPa. Given that a = 2.09 m and b = 1.48 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 66.49 MPa in the bronze and 85.69 MPa in the steel. Round off the final answer to two decimal places.
Q1: The shaft BC is hollow with inner and outer diameters of 100 mm and 120 mm respectively. Shaft AB and CD are solid and of diameter d. For the loading shown determine the maximum and minimum shear stress in shaft BC. 0.9 m 0.7 m d 0.5 m A 120 mm T = 10 kN.m i В TB = = 20 KN.m 1 C D Tc = 30 KN.mi Tp = 6 kN - m Figure Question1