The cantilever strut is subjected to the point loadsP₁ = 2.8 kN and P₂ = 5.6 kN. (Figure 1)Figure-250 mmaa250 mmP₁300 mm20 mmT70 mm20 mmB B50 mmPart ADetermine the maximum shear stress acting at section a-a of the cantilever strut.Express your answer to three significant figures and include the appropriate units.Tmax =μAValueUnits?

Answered: Image /qna-images/answer/b96fcc94-6c8e-442d-bc38-e656f9962040.jpg

The cantilever strut is subjected to the point loads P₁ = 2.8 kN and P₂ = 5.6 kN. (Figure 1) Determine the maximum shear stress acting at section a-a of the cantilever strut Express your answer to three significant figures and include the appropriate units.

The cantilever strut is subjected to the point loads P₁ = 2.8 kN and P₂ = 5.6 kN. (Figure 1) Determine the maximum shear stress acting at section a-a of the cantilever strut Express your answer to three significant figures and include the appropriate units.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.7P: The normal and shear stresses acting on element A are 6500 psi, 17,300 psi, and 2900 psi (see the...

See similar textbooks

Related questions

Q: The steel propeller shaft ABCD carries the axial loads shown in Figure. Determine the change in the…

A: Answer: The change in length of the shaft is 0.0136 in.

Q: The solid circular rod has a cross-sectional area of 310 mm2. It is subjected to a uniform axial…

Q: Question 4: Two wrenches are used to tighten the pipe. If the pipe is made from a material having an…

Q: roblems In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa.…

A: Givenallowable stress of rod σa=86.60MPaallowable shear stress on pin A=60MPadouble shear stress

Q: An L-shaped bracket lying in a horizontal plane supports a load F = 1kN. The bracket has a hollow…

A: Write the given information.

Q: Problem 1: A 35 mm diameter steel rod is embedded in a concrete block that is rigidly attached on a…

A: Tensile stress Tensile stress refers to a force that attempts to pull apart or stretch a material.…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6…

Q: 3. The bar in the figure is connected to the support using a pin having a diameter of 1.25 in. If…

A: As per given question Diameter of pin =1.25in Axial stress of bar =18 ksi Bearing stress =28ksi We…

Q: Determine the state of stress at point A on the cross section of the beam at section a-a. Take P =…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. The…

Q: Part A The bolted connection (Figure 1) joins the bar supporting force P to two flanges set into a…

A: As per given question We have to determine shear force of given bar

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6…

Q: The lap joint is connected by three 25-mm-diameter rivets. Assuming that the axial load P = 75 kN is…

Q: –L2 H K F1 L1 F2

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load Pat…

Q: Three solid bars, each with square cross sections, make up the axial assembly shown. Two loads of P…

A: b2 = 38.818 mm

Q: Concentrated loads of Px = 43 kips, Py = 29 kips, and P₂ = 52 kips are applied to the cantilever…

A: The concentrated load, Px = 43 kips, Py = 29 kips, Pz = 52 kipsThe dimensions, a = 7 in, b = 14 in,…

Q: Two wooden members are glued together as shown in the figure. Each member has a width of b = 1.25…

Q: PROBLEM 1. The dimensions of a bar made of a 2024-T6 aluminum alloy and the loads acting on it are…

A: EA1= 73*109pa Let AB is part 1 and BC is part 2 Considering factor of safety 1.5 load acting is…

Q: The lap joint is connected by three 20-mm-diameter rivets. Assuming that the axial load P=50 kN is…

A: Welding joints are used to join two different materials together. There are different types of…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6…

Q: Couple-moment M is applied to the beam, which has a cross-section, as shown in the Figure. if M =…

A: According to the question M=458 N.m β=62° We need to find Stresses at point A ,B and D

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 8…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 9…

A: According to the given data Diameter of the BD member =D=9 mm Pin at B is in double shear with…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 8…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of…

Q: Part A The bolted connection (Eigure 1) joins the bar supporting force P to two flanges set into a…

Q: The yoke and rod connection assembly shown in the figure below is subjected to a tensile force of 5…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6…

Q: The two wooden boards shown in Figure are connected by a 0.5-in.-diameter bolt. Washers are…

Q: Q2) For the problem shown in the figure, - Find the axial displacement at the end B - Determine the…

A: Given data, E = Modulus of elasticity = 50 MPa d1 = Inner diameter at the smaller end = 40 mm d2 =…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6…

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

100%

The cantilever strut is subjected to the point loads
P₁ = 2.8 kN and P₂ = 5.6 kN. (Figure 1)
Figure
-250 mm
a
a
250 mm
P₁
300 mm
20 mm
T
70 mm
20 mm
B B
50 mm
Part A
Determine the maximum shear stress acting at section a-a of the cantilever strut.
Express your answer to three significant figures and include the appropriate units.
Tmax =
μA
Value
Units
?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given information

VIEW

Step 2: Calculating the maximum shear stress acting at section a-a

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
A shock mount constructed as shown iu the figure is used to support a delicate instrument. The mount consists of an outer steel tube with inside diameter b. a central steel bar of diameter d that supports the load P, and a hollow rubber cylinder (height /r) bonded to the tube and bar (a) Obtain a formula Tor the shear stress t in the rubber at a radial distance r from the center of the shock mount. (b) Obtain a formula Tor the downward displacement S of the central bar due to the load P. assuming that G is the shear modulus of elasticity of the rubber and that the steel tube and bar are rigid.
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
What is the maximum possible value of the clamping Force C in the jaws of the pliers shown in the figure if the ultimate shear stress in the 5-mm diameter pin is 340 MPa? What is the maximum permissible value of the applied load P to maintain a factor of safety of 3.0 with respect to failure of the pin?
An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?