The brass shell (a = 11.6 x 10-6/F) is fully bonded to the steel core (a = 6.5 x 10-6/°F). Determine the largest allowable Increase in temperature if the stress in the steel core is not to exceed 7.8 ksl. in Steel core E = 29 x 10² psi Brass shell E-15 x 10 psi 1 in. 12 in The largest allowable Increase in temperature is *F.

The brass shell (a = 11.6 x 10-6/F) is fully bonded to the steel core (a = 6.5 x 10-6/°F). Determine the largest allowable Increase in temperature if the stress in the steel core is not to exceed 7.8 ksl. in Steel core E = 29 x 10² psi Brass shell E-15 x 10 psi 1 in. 12 in The largest allowable Increase in temperature is *F.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The assembly consists of a bronze tube fitted over a threaded steel bolt. The nut on the bolt is turned until it is finger-tight. Determine the stresses in the sleeve and bolt when the temperature of the assembly is increased by 200°F. Use the following data: Bronze Steel A (in. ²) 1.5 0.75 a (/°F) 10 × 10-6 6.5 x 10-6 Bronze tube 40 in. E (psi) 12 × 106 29 × 106 STA UT TEO
ll ? The rod BD is made of material with G1= 135 GPa has a diameter 16 mm is bonded to the tube CA at point B, the tube made of material with G2=230o GPa has an outer diameter 37 mm and wall thickness of 7 mm. li T1=803 N.m and T2=1445 N.m, answer the following questions: B T2 Nm 04 m 0.1 m 0.3 m TI N-m The polar moment of inertia of the rod BD is Your answer The polar moment of inertia of the tube CA is
3) At room temperature (20 °C) a 0.8 mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 120 °C, determine (a) the normal stress in the aluminum rod, (b) the change in length of the aluminum rod Bronze: Aluminum: Steel: Area: 1000 mm2 Area: 2000 mm2 Area: 1500 mm2 a = 18.4 x 10-6 E = 103 GPa a = 23.6x 10-6 E = 75 GPa a = 17.3 x 10-6 E = 190 GPa %3D %3D 0.8 mm 100 mm 150 mm 300 mm Bronze Al Steel
At a temperature of 33.01 °C a 0.46-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 138.98°C, determine the magnitude of the normal stress (in MPa) in the steel rod if L = 304.28 mm and M = 209 mm. Round off the final answer to four decimal places.
None
Current Attempt in Progress A solid prismatic rod is L; = 330 mm long and has a circular cross section with a diameter of d = 24 mm. After the temperature of the unconstrained rod is increased, its final length is measured as L₁= 330.265 mm. Determine the change in the rod's diameter after the temperature increase. Answer: Ad = i mm
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ = 13 kips, F₂ = 34 kips, and the normal stress in each rod must be limited to 22 ksi, determine the minimum diameter d₁ required for rod (1). A (2) d₁ F₂ B C O 1.087 in. O 0.823 in. O 0.541 in. O 0.867 in. O 1.003 in. d₂
Tind the stresses in the steel and aluminum rods when the temperature rises to 60 C° and the distributed load is 10 kN/m. Given: Steel Rod E = 200 GPa L = 1.499 m 10KN/m esmott A = 80 mm? oc= 12 x 10-6 1/°c Gap 1 mm Aluminum Rod Steel Rod Aluminum Rod E = 70 GPa L = 1.5 m A = 200 mm? x= 22 x 10-6 1/°c Figure (2) !! 2 m 2 m
a=2.1m (1) c = 2m b = 3.1m d = 1.8m P = 80 kN WHAT IS THE AXIAL STRESS IN ROD 1 ? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES B dia. of rod 1: = 13mm dia of rod 2 = 11 mm
Determine normal stress.
Two aluminum plates, each having a width of b = 8.0 in. and a thickness of t = 0.750 in., are welded together as shown. Assume a = 4.0 in. For a load of P = 75 kips, determine (a) the normal stress that acts perpendicular to the weld and (b) the magnitude of the shear stress that acts parallel to the weld. Answer: O= P T = 1 i 1 ksi ksi b P
A rigid horizontal bar ABC is supported by three vertical rods as shown. The system is stress free before the load is applied. After the load P is applied, the temperature of all three rods is raised by 110°F. Determine the magnitude of the normal stress in rod (1). Answer in MPa rounded-off to 2 decimal places. Rod (1) : E = 105 GPa; a= 22.0 x 10-5/°C A=500 mm² Rod (2): E = 200 GPa; a = 11.7 x 10-6/°C A=250 mm² 2,100 mm 4,400 mm (1) (2) B (2) P= 45 KN 2,100 mm I