When installed, bar AB had negligible axial stress. When the bar'stemperature is 124°F the axial compressive stress is 14.4 ksi. The bar is made from aductile metal which has the following properties: E=25x10° psi,a = 9.00x10 6 (h)/°F, and v = 0.29. Assume elastic behavior.( in.in.В50 in.-Determine:a. The thermal strain in the bar's axial (longitudinal) direction if it could expandfreely:b. Temperature at which bar was installed:c. The total strain in the lateral direction:

Given : A bar AB had negligible stress axial stress when installed . When bar temperature is…

When installed, bar AB had negligible axial stress. When the bar's temperature is 124°F the axial compressive stress is 14.4 ksi. The bar is made from a ductile metal which has the following properties: E=25x10° psi, a = 9.00x106 (n.)/°F, and v = 0.29. Assume elastic behavior. in. 50 in.

When installed, bar AB had negligible axial stress. When the bar's temperature is 124°F the axial compressive stress is 14.4 ksi. The bar is made from a ductile metal which has the following properties: E=25x10° psi, a = 9.00x106 (n.)/°F, and v = 0.29. Assume elastic behavior. in. 50 in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 5: The following 0.8" diameter steel bar has three loads applied, as shown. Assuming that E= 30,000,000 psi, determine the following: Stress at points A, B, and C Total elongation of the bar. Hint: 8- PL AE オー 2000 Ibs 2-0" 4000 Ibs I-0 7000 Ibs
A steel rod with a cross-sectional area of 0.25in .^ 2 is stretched between two fixed points. The tensile load at 0.7 deg * Fis * 1200 lb. What will be the stress at 0 deg * F ? At what temperature will the stress be zero? Assume alpha = 6.5 * 10 ^ - 6 in ./(in*^ F) and E = 29 * 10 ^ 4 psi.
Q2: A spacer is turned from Aluminum alloy with elasticity modulus of 78 GN/m?. The spacer has a diameter of 28 mm and a length of 245 mm. both measurements being made at 20°C. The temperature of the spacer is then increased to 100 °C, the natural expansion being entirely prevented. Taking the coefficient of linear expansion to be 18 x 10-6 °C. Determine the compressive load on the spacer.
The blue bar is made from steel with the following mechanical properties: Young's Modulus, E = 17x10° psi; Poisson's Ratio v = 0.31. The bar has a circular cross-section with diameter d= 0.50 in. being the length of each side. 557 lb 557 Ib 60 in. - Determine the following under the action of the axial load (assume elastic behavior): a. The bar's axial deformation, ô, in in.: b. The average axial or longitudinal strain, ELong: c. The change in the bar's diameter, in in.:
The state of stress shown below is from the surface of a bar under axial and torsion loading. Calculate the principal stresses and directions (i.e, the value of the angle 0). Draw the state of stress aligned with the principal directions. 60 MPa T 9. 40 MPa 40 MPа
Problem 1: A steel rod with a cross-sectional area of 0.20 in´ is stretched between two fixed points. The tensile load at 65°F is 1250 lb. What will be the stress at 0°F? At what temperature will the stress be zero? Assume a = 6.5×10° in / (in.°F) and E = 29 x 10° psi.
Q1: 30-mm-diameter steel bar is to be used as a torsion spring. If the torsional stress in the bar is not to exceed 110 MPa when one end is twisted through an angle of 30°, what must be the length of the bar in m? modulus of rigidity=80 GPa . (close to two decimal)
E. Rigid bar AD is horizontal before the weight of 112 lb is applied to the end of wire BC at C. The wires have a radius of 0.025" and are made of A913 steel. Determine the rotation of AD and how far C will move down due to application of the weight See Appendix of text for any material properties needed. Ans: 0.00071 radians 3 ft - 2 ft -3 ft- D B 4 ft W
Determine the maximum axial force that can be applied to the bar shown in Figure 3. The allowable stress is 100 MPa. The dimensions are: Hole diameter 20 mm. Thickness of bar: 6 mm D = 40 mm d%3D20mm Fillet radius, r = 4 mm 40mm 20 mm r 4 mm 20 mm Figure 3 P.
The bar is made from steel and has an allowable stress of allow = 19.7 ksi (Figure 1) Figure P 1.875 in. 0.75 in. -0.125 in. 1.25 in. r 0.25 in. 1 of 1 Part A Determine the maximum axial force P that can be applied to the bar. Express your answer to three significant figures and include the appropriate units. P = Submit μA Value Request Answer < Return to Assignment Units Provide Feedback ?
1.2 Figure 1 show a compound bar made of the aluminum alloy with three different cross-sectional. The bar is subject to a tensile load of 40KN. Take E = 69 GPa, Determine the stress in each section and the total elongation of the bar 30 mm 40 mm 50 mm 40 kN 40 kN 0= 20 mm 0= 15 mm 0 = 10 mm