The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 28 mm. Assume L = 1.2 m and θ = 25°. If the average shear stress in the pins at A, B, and C cannot exceed 120 MPa, determine the maximum distributed load wmax that can be supported by the structure. answer: Wmax=_______________kN/m

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 11 kN applied at A. Assume a…

A:

Q: The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 26 mm. Assume…

A:

Q: Answer: Wmax = kN/m B

A: According to the given dataL=1.7md=18mmWe need to find the uniform distributed load w

Q: Figure 2 shows the loads supported by a steel rod (E = 200 GPa) with a diameter of 30 mm Neglecting…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 14 kN applied at A. Assume a…

A: Given data: F1=14 kNa=290 mmb=110 mmc=70 mmθ=40°dp=25 mmt=25 mm Need to determine the shear stress…

Q: 1. The structure is used to support a distributed load of w = 15 kN/m. The bolts at A, B, and C each…

A:

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 19 kN applied at A. Assume a…

A:

Q: If the allowable bearing stress for the material under the supports at A and B is ob = 600 psi,…

A:

Q: If the allowable bearing stress for the material under the supports at A and B is o₂ = 810 psi,…

A: FBD

Q: The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 16 mm. Assume…

A:

Q: If the allowable bearing stress for the material under the supports at A and B is b = 800 psi,…

A: Given that: Cross sectional area of the beam  = 5*5 in2 Maximum stress = 800 psi Under the given…

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

A:

Q: The overhanging beam is made of wood having the allowable tensile and compressive stresses of…

A: Given:           σallowt​=4MPa           σallowc​=4.25MPaSolution: 1) Shear and Moment Diagram…

Q: allowable bearing stress for the material under the supports at A and B is σ₂ = 780 psi, determine…

A:

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

A:

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

A:

Q: The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the largest vertical…

A: Givenσallowable=55ksi∆Climited=0.17inL=4ft=48 inchA=0.5in2E=29×106 psi

Q: A rectangular column is made of a grade of sawn wood that has an adjusted allowable stress for…

A: Write the given data. σC=8.3 MPaE=11.1 GPaP=105 kNe=0.025 mb=0.180 md=0.240 m

Q: B D The rods AB and CD are assumed to be pin connected at A and C. If the cable BD and CD are made…

A: Draw the free body diagram as follows.

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross- sectional…

A:

Q: A rectangular column is made of a grade of sawn wood that has an adjusted allowable stress for…

A: Write the given data. σC=8.3 MPaE=11.1 GPaP=88 kNe=0.025 mb=0.180 md=0.240 m

Q: If the allowable bearing stress for the material under the supports at A and B is O₂ = 840 psi,…

A: Answer: Pmax = 11600 lb

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

A:

Q: The steel column has an outer diameter of 4 in. and inner diameter of 3.5 in. is carrying a load P =…

A: Find the compressive stress of the column. Find bearing stress of the concrete. Find the punching…

Q: The beam is supported by a pin at Cand by a short link AB. Each pin has a diameter of 26 mm. Assume…

A:

Q: The rigid beam is supported by a pin at C and an A-36 steel guy wire AB. Part A If the wire has a…

A:

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

A:

Q: The beam is supported by a pin at Cand by a short link AB. Each pin has a diameter of 10 mm. Assume…

A:

Q: The allowable shear stress is Tallow = 805 psi. The supports at A and B are smooth. B 3 ft 6 ft -3…

A: Find the maximum allowable distributed load Given data  Maximum shear stress = 805 psi

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

A:

Q: The beam is supported by a pin at Cand by a short link AB. Each pin has a diameter of 12 mm. Assume…

A:

Q: If the allowable bearing stress for the material under the supports at A and B is σb = 840 psi,…

A:

Q: If the allowable bearing stress for the material under the supports at A and B is ob = 720 psi,…

A: FBD

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

A: Fro the given truss, Cross sectional area of each member = 3.3 in2 Maximum allowable stress = 25 ksi…

Q: The five-bolt connection must support an applied load of P = 1800 lb. If the average shear stress in…

A: Solution:     dmin = 0.0987 in

Q: The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 26 mm. Assume…

A:

Q: If the allowable bearing stress for the material under the supports at A and B is ob = 620 psi,…

A: To Find : The maximum load Pmax. Given :  The allowable bearing stress is σb=620 Psi. The  uniform…

Q: The five-bolt connection must support an applied load of P = 4600 lb. If the average shear stress in…

A:

Q: EVENTS CEV Opsi, determine the maximum load Pmax that TL

A:

Q: The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 20 mm. Assume…

A: Length of the link BCAngle made by link AB from the horizontal:Diameter of each pinSo the area of…

Q: Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.