The rigid beam is supported by a pin at C and an A-36 steel guy wire AB. Part A If the wire has a diameter of 0.2 in., determine the distributed load w if the end B is displaced 0.25 in. downward. Express your answer to three significant figures. ΠΑΣΦ W = vec ? kip ft W -10 ft 30° B

The rigid beam is supported by a pin at C and an A-36 steel guy wire AB. Part A If the wire has a diameter of 0.2 in., determine the distributed load w if the end B is displaced 0.25 in. downward. Express your answer to three significant figures. ΠΑΣΦ W = vec ? kip ft W -10 ft 30° B

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.9.23P

See similar textbooks

Related questions

Q: Determine the elongation of the bar in Problem when both the load P and the supports are removed.

A: Given data Length of the bar AB LAB = 5 ft To determine elongation of the bar when both the load P…

Q: The bar has a cross-sectional area A and is subjected to the axial load P. At what angle (in…

Q: The ultimate stress for a hollow steel column which carries an axial load of 1.9MN is 480N/mm if the…

Q: determine its new length

Q: The rigid arm AB is attached to the end of the solid circular steel rod BC. The rod is supported by…

Q: A-36 steel column has a length of 5 ft, is fixed at its bottom and pinned at its top. If the cross…

A: Given, L = 5 ft Pinned joint (k) = 1L E = 29 x 103 ksi σy = 36 ksi Area of the colomn:A =…

Q: Determine the Euler Buckling axial compressive load of W 12 x 72 section having a length of L=48 ft…

A: To find: The Euler Buckling load. Given: The length of the column, L = 14.63 m. Young's modulus, E =…

Q: Provide final answer and equations used.

Q: Axial loads are applied to the compound rod that is composed of an Aluminum segment rigidly…

A: Given:As=400 mm2Aa=500 mm2Ab=300 mm2P=12 kN

Q: e rigid beam is supported by a pin at C and an A-36 steel guy wire AB.

A: Given: The diameter of wire is, d=0.4 in. The distribution load is, w=100 lb/ft. The length of the…

Q: A rectangular column is made of a grade of sawn wood that has an adjusted allowable stress for…

A: Write the given data. σC=8.3 MPaE=11.1 GPaP=105 kNe=0.025 mb=0.180 md=0.240 m

Q: Determine the critical axial buckling load for an 8 3/4 x 12 inches glue-laminated column braced at…

A: In the question , given that, E = young modulus of elasticity (1.8×106psi) dimension of column ,…

Q: sectional area of Arod = 0.75 in². If a load of P = 24 kip is applied to the end of rod, determine…

Q: A column with rectangular cross section of breadth = 9mm and depth = 4mm, has its both ends are…

Q: If the maximum stress both in tension and compression is not to exceed 120 Mpa, determine the…

A: Step 1: Step 2: Step 3: Step 4:

Q: The allowable shear stress is Tallow = 805 psi. The supports at A and B are smooth. B 3 ft 6 ft -3…

A: Find the maximum allowable distributed load Given data Maximum shear stress = 805 psi

Q: Determine the radius of the round strut so that the round and square struts have the same…

A: Given data: The young’s modulus, E = 200 GPa. Calculate the area of the square struts. A=25 mm×25…

Q: The rods AB and CD are made of steel. Determine their smallest diameter so that they can support the…

A: Given: The dead load factor is gD=1.4. The stress due to failure is бfailure=345 MPa. The…

Q: The shears shown are exerting a vertical force on the branch at point E. Find the load in 2-force…

Q: A hollow A36 steel rod is loaded and supported as shown. Determine the stress in each side and the…

A: From the given data, Modulus of elasticity: E = 200 GPa (For steel rod)

Q: The rigid beam is supported by a pin at C and an A-36 steel guy wire AB. Part A If the wire has a…

Q: diameter brass rod. In order to reduce the weight of the member by 25%, the solid rod is replaced by…

Q: Two solid cylindrical rods support a load of P = 25 kN as shown. Determine the axial load in rod…

Q: A round brass rod 30 mm in diameter and 200 mm long is subjected to a compressive force of 100 kN.…

Q: Required information A 1-in.-square aluminum strut is maintained in the position shown by a pin…

A: Solution: Given Data: A=1 in2LAB=3.4 ftE=10.4×106 psiFOS=3.2 To Find; The magnitude of the…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

The rigid beam is supported by a pin at C and an A-36 steel guy wire AB.
Part A
If the wire has a diameter of 0.2 in., determine the distributed load w if the end B is displaced 0.25 in. downward.
Express your answer to three significant figures.
ΠΑΣΦ
W =
vec
?
kip
ft
W
-10 ft
30°
B

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

If the rods are made from a square section with the dimension as shown. Calculate the load that will make point A move to the left by 6mm, E=228GPa. 2P- P A 80mm B 200mm 2P 0.9m 1.3m
Provide final answer and equations used.
Problem #2: The strut is by a pin at C and a A-36 steel guy wire AB (E = 200 GPa). If the wire has a diameter 5 mm, determine how much it stretches when the distributed load acts on the strut. A 60° 3.4 kN/m В 2.7 m Solve only by using this Donot nse equation &= AS'-AS AE
The rigid pipe is supported by a pin at A and an A-36 guy wire BD. The wire has a diameter of 0.27 in. Determine the load P if the end C is displaced 0.075 in. downward.
The bar is connected to the support using a pin having a diameter of d =lin. If the allowable tensile stress for the bar is (o,)low = 20ksi , and the allowable bearing stress between the pin and the bar is (0,)allow = 30ksi , determine the dimension w and t so that the gross area of the cross section is wt = 2in² and the load P is a maximum. What is this maximum load? Assume the hole in the bar has the same diameter as the pin. (Hint: Use the prjjected area whenj calculating the bearing stress.) t d w/2 w/2
The rigid beam is supported by a pin at C and an A-36 steel guy wire AB. Part A W If the wire has a diameter of 0.4 in., determine how much it stretches when a distributed load of 100 lb/ft acts on the beam. The material remains elastic. Express your answer to three significant figures and include appropriate units. Submit 10 ft SAB = Value Provide Feedback Request Answer Units ?
5. The hanger is supported using the rectangular pin. Determine the magnitude of the allowable suspended load P if the allowable bearing stress is b,allow = 220 MPa, the allowable tensile stress is at,allow = 150 MPa, and the allowable shear stress is Tallow = 130 MPa. Take t = 6 mm, a = 5 mm and b = 25 mm. 75 mm 37.5 mm 20 mm 10 mm 37.5 mm
The rods AB and CD are made of steel. Determine their smallest diameter so that they can support the dead loads shown. The beam is assumed to be pin connected at A and C. Use the LRFD method, where the resistance factorfor steel in tension is f = 0.9, and the dead load factor is gD = 1.4. The failure stress is sfail = 345 MPa.
A small stepladder has vertical rails and horizontal steps formed from a C-section aluminum channel. Two rivets, one in front and one in back, secure the ends of each step. The rivets attach the steps to the left and right hand rails. A 225 lb person stands in the center of a step. If rivets are formed of 6061-T6 aluminum, what should be the diameter d of the rivets? Use a factor of safety of 8 and round your answer to the nearest 1/16 of an in.
Solve this problem and show all of the work
kips. Determine the Euler Buckling axial compressive load of W 12 x 72 section having a length of L=48 ft and fixed ends, Pe= Assume that the column is made of A441 steel with E = 29 x 103 ksi, and assume that the normal stress generated by P is still within the elastic range of the material. Reminder: use the minimum moment of inertial of the cross section. Please calculate your answer to 1 decimal place. Lft Fixed end Fixed end
The copper bar is subjected to a uniform loading shown in Fig. 10–24. Ifit has a length a = 300 mm, width b = 50 mm, and thickness t = 20 mmbefore the load is applied, determine its new length, width, and thicknessafter application of the load. Take Ecu = 120 GPa, ncu = 0.34.