The allowable shear stress is Tallow = 650 psi. The supports at A and B are smooth. Part A Determine the largest intensity w of the distributed load that the member can support. Express your answer to three significant figures. A -3 ft- 1 in. 6 ft 2 in, I in. B 2 in. 3 ft 6 in.

Q: The steel bracket is used to connect the ends of two cables. Y Part A O max = If the applied force P…

A: P=d=To determine:The maximum normal stress

Q: Bar (1) has a cross-sectional area of 0.75 in.². If the stress in bar (1) must be limited to 39 ksi,…

A: Correct answer: (b) 17.55 kips

Q: The hook is subjected to the force of 60 lb Determine the state of stress at point A at section a-a.…

A: Part A: Write the given data. F=60 lbd=0.5 in

Q: The state of stress at a point in a member is shown on the element below. If: 0x = 9 MPa Oy=-14 MPa…

A:

Q: The concrete post is reinforced using six steel reiforcing rods, each having a diameter of 20 mm.…

A: Given data: Diameter of each rod = d = 20 mm Applied axial load = P = 900 kN Modulus of elasticity…

Q: The boom is supported by the winch cable that has an allowable normal stress of allow = 24 ksi. It…

A:

Q: 1. (50 pts) A beam is fixed on one end and free on the other. It has an open circular cross-section…

A: The objective of the question is to determine the stress state at points A, B, C, D and the maximum…

Q: The beam supports the triangular distributed load shown below with Wmax = 510 lb/ft. The reactions…

A: According to the question data triangular loading beam is given we need to determine the internal…

Q: The pipe assembly is subjected to the loads shown. Determine the state of stress at point A on…

A: Given data, Let Ax, Ay and Az are the reaction force at A Bx and Bz are the reaction force at B Cz…

Q: a. Use Mohr's Circle to determine the maximum shear stress on the element b. Also, using Mohr's…

A: Mohr's circle for, σx=-30MPaσy= 50MPaτxy= 20MPa

Q: The allowable shear stress is Tallow = 805 psi. The supports at A and B are smooth. B 3 ft 6 ft -3…

A: Find the maximum allowable distributed load Given data  Maximum shear stress = 805 psi

Q: The assembly supports a uniform distributed load = 1.65 kN/m as shown. Part A Determine the…

A:

Q: The circular punch B exerts a force of P = 1.7 kN on the top of the plate A. (Figure 1) Figure <) 1…

A:

Q: The beam is made from two plastic pieces glued together at the seam A.  If it is subjected to the…

A: Answer: The vertical shear force resisted by the flange of the beam at the critical section is…

Q: The steel bracket is used to connect the ends of two cables Part A O max If the applied force P= 1…

A: Given that,Applied force = P = 1 kipDiameter of rod of bracket = d = 2.25 inTo find:The maximum…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.