The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 26 mm. Assume L = 1.7 m and 0 = 25°. If the average shear stress in the pins at A, B, and C cannot exceed 110 MPa, determine the maximum distributed load wmax that can be supported by the structure. B L Answer: Wmax i kN/m

The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 26 mm. Assume L = 1.7 m and 0 = 25°. If the average shear stress in the pins at A, B, and C cannot exceed 110 MPa, determine the maximum distributed load wmax that can be supported by the structure. B L Answer: Wmax i kN/m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The allowable shear stress is Tallow 805 psi. The supports at A and B are smooth. -3 ft 6 ft - 3 ft. 2 in. 6 in. I in. 2 in. I in. Part A Determine the largest intensity w of the distributed load that the member can support. Express your answer to three significant figures. vec Wmax = kip/ft
Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear and have a diameter of 0.625 in. Assume L = 3.5 ft. If the average shear stress in the bolts cannot exceed 70 ksi, determine the maximum distributed load Wmax that can be supported by the structure. F₁ B L (1) Answer: Wmax kips/ft =
The beam is supported by a pin at Ċ and by a short link AB. Each pin has a diameter of 12 mm. Assume L = 1.2 m and 9 = 35°. If the average shear stress in the pins at A, B, and C cannot exceed 125 MPa, determine the maximum distributed load Wmax that can be supported by the structure. A e Answer: Wmax i B W L kN/m
The bar is connected to the support using a pin having a diameter of d =lin. If the allowable tensile stress for the bar is (o,)low = 20ksi , and the allowable bearing stress between the pin and the bar is (0,)allow = 30ksi , determine the dimension w and t so that the gross area of the cross section is wt = 2in² and the load P is a maximum. What is this maximum load? Assume the hole in the bar has the same diameter as the pin. (Hint: Use the prjjected area whenj calculating the bearing stress.) t d w/2 w/2
If the allowable bearing stress for the material under the supports at A and B is ob = 720 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 3 in. by 3 in. The reactions at the supports are vertical. Assume w = 750 lb/ft, a = 12 ft, and b = 6 ft. Answer: Pmax i b lb P
The tube has an inner diameter d; = 20 mm and an outer diameter d, = 22 mm. It is subjected to an internal pressure of 1 MPa and the loads shown below. Determine the stress at point A and draw it on a stress element. 200 mm 400 mm 150 N-m 600 N 1500 N 800 N
A4
The steel bar has the original dimensions shown in the figure. If it is subjected to an axial load of 50 kN, determine the change in its length and its new cross-sectional dimensions at section a–a. Est = 200 GPa, nst = 0.29.
A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional area of A = 3.7 in.². Assume a = 3.00 ft and b = 3.60 ft. If the normal stress in each member must not exceed 35 ksi, determine the maximum load Pmax that may be supported by the structure. A Answer: Pmax= b B b kips
A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 1480 mm2. Assume a = 1.3 m, b = 6.0 m, and c= 3.6 m. If P = 55 kN and Q = 75 kN, determine the normal stress in each member. P 0← L. Answers: OAB = i OBC= i JAC = i a B MPa (C) MPa (T) MPa (T)
If the allowable bearing stress for the material under the supports at A and B is 0,730 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 3 in. by 3 in. The reactions at the supports are vertical. Assume w=550 lb/ft, a = 10 ft, and b = 5 ft. Answer: Pmax= b Ib
The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 20 mm. Assume L = 1.5 m and 0 = 35°. If the average shear stress in the pins at A, B, and C cannot exceed 120 MPa, determine the maximum distributed load Wmax that can be supported by the structure. EP e B Answer: Wmax= i kN/m L C H