Figure 2 shows the loads supported by a steel rod (E = 200 GPa) with a diameter of 30 mm Neglecting the size of the couplings, determine (a) the displacement of end A with respect to end E. (b) the factor of safety if the maximum normal stress in the rod is 50 MPa 8KN 4 kN 6 KN 2 KN 4 m 2 m 2 m 2 m Figure 2

Figure 2 shows the loads supported by a steel rod (E = 200 GPa) with a diameter of 30 mm Neglecting the size of the couplings, determine (a) the displacement of end A with respect to end E. (b) the factor of safety if the maximum normal stress in the rod is 50 MPa 8KN 4 kN 6 KN 2 KN 4 m 2 m 2 m 2 m Figure 2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Aluminum Rod Allowable tension stress = 100 Mpa Steel Rod allowable tension Cross section 30 x 5 mm L = 500 mm E - 70 GPa stress 120 MPa Cross section 20 x 5 mm L- 300 mm E = 200 GPa Rigid bar 600 mm 400 mm W T 12 mm diameter bolt alowable shear stress - 50 MPa alowable bearing stress - 80 MPa 15 5mm 5mM Determine the alowable maximum load W that can be applied if the rigid bar should remain horizontal
I need help on solving this question
For the hollow shaft shown, the strength is 150 MPa. Determine 1. The internal reactions due to external loads Fe. 2. Factor of safety for this bar Di=10 mm Fe=40 kN Do=30 mm
Problem 3. A solid round bar is to be assembled into a collar by press fitting. The inside radius of the collar is R = 50 mm and the outside radius is o = 4C mm. Find the maximum allowable radial interference 3 if the assembly is to have a safety factor of 2 against yielding. Both parts are made of carbon steel having E 200 GPa and Sy = 300MPa Solve using the DET. ↑ O
A shaft fixed to a wall at B is made of an outer steel tube of 1" outer radius (G = 11,400 ksi) bonded to an inner solid brass core (G = 5200 ksi) of 0.5" radius. For the torque applied at A determine the maximum shear stress in each material and the rotation of A. Note: Each material carries part of the total applied torque. Treat end A %3D as a joint. Ans: 1977 psi steel, 451 psi brass 4 ft 0.5 in. 1 in. T= 250 lb-ft (a) all cunnorted at A and B. For
The 24-mm-diameter A-36 steel rod is subjected to the axial forces shown. Take E = 200 GPa. (Figure 1) Figure 600 mm B 400 mm 50 kN 50 kN C 40 kN 1 of 1 > ▾ Part A Determine the displacement of end C with respect to the fixed support at A. Express your answer to three significant figures and include the appropriate units. dc = Submit μA Value Provide Feedback Request Answer Units ? 4
QI\ Determine the elongation of the system shown in figure below 100 kN 50 kN 50 kN steel Copper E=117GPA Bronze E=210GPA E=82GPA A=1500mm A=1000mm A=500mm
Bar of steel, (yield strenght Sy = 474 MPa) is subjected to the following stresses; σx = 194 MPa , σy = 100 MPa , τxy = 210 MPa Using the Maximum Shear Stress Theory (MSS) determine the factor of safety and check is the bar will fail or not.
In the element in the figure, the bars are made of UNSG 10100 HR steel (Sy= 26 Kpsi and E= 30x106 psi). Determine the maximum weight that the system can support.
A bronze c86100 cylinder with diameter d2 = 60 mm is nested inside a stainless steel tube with inner diameter of d₁ = 80 mm L = 250 mm and wall thickness of t = 10 mm. The bronze cylinder is 1 mm taller than the stainless steel tube. What is the largest axial load, P, that can be applied without either material yielding? For this problem, use Eb = 103 GPa, Est = 193 GPa, σy,br=345 MPa, σy.st=207 MPa. P B L BY NO SA 2021 Cathy Zupke d₂ t The maximum load before yielding is P = KN
8
Rigid member AB is supported by hinge support at A and a 12-mm-diameter wire BC at B as shown. The diameter of the pin at A is 10 mm, thickness of member AB is 20 mm, and the thickness of each bracket of support A is 15 mm. Use a factor of safety FS= 2 and following failure stresses to determine the maximum load w (kN/m) the member can support. For wire BC: G=350 MPa Pin at A: Ta=200 MPa Support brackets: (Gharn n=150 MPa d-12 -35m 3m 20 mm smm Member AB- 10 mm Support Bracket- Support Bracket Conection detail at EpetA