The bar has a cross-sectional area of 480(109 m². It is subjected to a triangular axial distributed loading along its length which is 0 kN/m at æ = 0 m and 9 kN/m at x = 1.5 m, and to two concentrated loads as shown. -8 kN 4 kN 0.6 m 0.9 m Part A Determine the average normal stress in the bar as a function of x for 0 m < æ < 0.6 m. 39.06x² + 6.25 39.06 – 6.25º2 o(x) = MPа 39.06 + 6.25x² 39.06x² – 6.25

The bar has a cross-sectional area of 480(109 m². It is subjected to a triangular axial distributed loading along its length which is 0 kN/m at æ = 0 m and 9 kN/m at x = 1.5 m, and to two concentrated loads as shown. -8 kN 4 kN 0.6 m 0.9 m Part A Determine the average normal stress in the bar as a function of x for 0 m < æ < 0.6 m. 39.06x² + 6.25 39.06 – 6.25º2 o(x) = MPа 39.06 + 6.25x² 39.06x² – 6.25

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the state of stress at point A on the cross section at section a-a of the cantilever beam. The moment area of inertia of the I beam about its horizontal neutral axis is INA= 0.225 x 103 m4. 0= T= 100 mm 300 mm 100 mm Section a-a a 400 KN -0.5 m- 70.2 Mpa (Compression) 37.8 Mpa (Compression) 18.2 Mpa (Compression) 8.9 Mpa 17.8 Mpa 33.5 Mpa 150 mm 200 kN
If the load has a weight equivalent to 5 kN, determine the maximum normal stress on the cross section of the supporting member at section a-a. The cross section of the supporting member is circular with radius of 2 cm. The vertical supporting member CD is 50 cm away from the AB line. C 50 cm 2 cm a a В Section a – a
The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 14 mm. Assume L = 1.1 m and 0 = 20°. If the average shear stress in the pins at A, B, and C cannot exceed 125 MPa, determine the maximum distributed load Wmax that can be supported by the structure. (1) 0 Answer: Wmax i B kN/m C
If the extended stress at the point p in the level and at i+j+ k is given by matrix 10 2 2 22 the component Tnx = 231 1 %3D nx V3 nx V3 aņl wrong %3D
Determine if the stress in the steel section, aluminum section, and bronze section are compression or tension
The rigid bar ABC pivots about support B. After application of load P, end C of the rigid bar moves upward by 0.07 in. If the length of bar (1) is L₁-41 in, determine the average normal strain in bar (1). Assume that a-135 in, b-39 in, and c-0.15 in a b C Rigid bar 4 Part 1 * Incorrect Determine the distance that end A of the rigid bar moves downward, if end C moves upward by 0.07 in Answer: in VA i 00361
The three suspender bars are made of steel and have equal cross-sectional areas of 450 mm?. Determine the average normal stress in each bar if the rigid beam is subjected to the loading shown. A В C 80 kN 2 m 50 kN D E -1 m- +1m- 1m-1 m-|
The rigid bar ABC pivots about support B. After application of load P, end C of the rigid bar moves upward by 0.06 in. If the length of bar (1) is L₁ = 51 in, determine the average normal strain in bar (1). Assume that a = 135 in., b=32 in., and c = 0.06 in. 4₁ 1 a Rigid bar B b
Determine the value of the maximum shear stress and the maximum normal stress produced in the structure shown, based on the cross section.
A lever is attached to a shaft with a square shear key as shown. If the force applied to the lever is P = 395 N, determine the shear force applied to the shear key. 42 mm. ↓ Shear key O 10.90 KN O 18.31 KN O 9.70 KN O 14.25 KN O 13.17 kN 700 mm C Shear key detail
4. The member has a square cross section and is subjected to moment M = 850 Nm which acts in an angle of 0 = 30°. Determine the stress at each corner A, B, D and E. 250 mm B 125 mm D 125 mm 8 M M = 850 N-m
The pole is supported by a pin at B and A-36 steel guy wire AC. If the wire has a diameter of 0.2. Modulus of Elasticity of Steel = 200GPA or 29x103 ksi Poisson's ratio of steel=0.321 a. Determine how much the wire stretches when the horizontal force acts on the pole. 3 ft 30 D 2.5 kip 4 ft B b. Determine the change in the wire's radius c. At what angle is the principal stresses on pole BC? Use Mohr's Circle. d. What is the principal stress in pol BC? Use Mohr's Circle e. Draw the stresses on a unit element acting on 35-degree clockwise direction of pole BC. Use Mohr's Circle. f. What are the principal stresses in point D? Use Mohr's Circle. (answer in ksi) g. At what angle is the principal stresses acting on point D? Use Mohr 's Circle. h. Draw the stresses on a unit element acting on 35degree-clockwise direction of point D. Use Mohr's Circle. (answer in ksi)